AR01.45-W-7500C | Remove/install oil pan | 21.10.11 |
ENGINES 904.9 in MODELS 374, 375, 958, 970, 972, 975, 976
ENGINES 906.9 in MODEL 374, 958, 970, 972, 974, 975, 976
ENGINES 906.9 in MODELS 374, 375, 950, 952, 953, 954, 958
W01.45-0005-06
1 Oil pan
2 Seal
3 Screw/bolt
4 Oil filling line
5 Sealing ring
6 Oil drain screw
7 Engine wiring harness
B14 Oil level sensor
| Remove/install | ||
Danger! | Risk of injury caused by body parts being pinched or crushed as cab is tilted | Ensure that no one is within tilting range of cab as it is being tilted. Always tilt cab all the way to end position and secure with safety strut. | |
1 | Tilt cab | ||
| Notes on tilting the cab | ||
2 | Extract or drain engine oil | ||
| |||
| |||
Engine oil extractor | |||
3 | Detach oil filler line (4) at oil pan (1) | ||
4 | Separate electric engine wiring harness (7) from oil level sensor (B14) and expose electrical line of oil level sensor (B14) | ||
5 | Dismantle transmission oil lines at brackets and tie to one side | Only with code (N55) Transmission oil cooling. Do not disconnect transmission oil lines. | |
6 | Unscrew screw/bolts (3) and take off oil pan (1) | Installation: Clean sealing surfaces and install a new seal (2). | |
| |||
7 | Remove oil level sensor (B14) | Only when installing a new oil pan (1). | |
| |||
8 | Install in the reverse order | ||
9 | Check engine oil level using oil dipstick or on display, correct if necessary | Observe engine oil grade set in maintenance system or Specifications for Operating Fluids. | |
Danger! | Risk of accident caused by vehicle starting off by itself when engine is running. Risk of injury caused by contusions and burns during starting procedure or when working near the engine as it is running | Secure vehicle to prevent it from moving by itself. | |
10 | Start engine and observe oil pressure gauge with the engine idling | Crank engine with the starter for not more than 90 seconds. Wait for about 2 minutes before repeating starting attempt. Do not rev up engine before oil pressure is indicated. The oil pressure gauge must indicate oil pressure after about 10 seconds. | |
11 | Switch off engine and check for leaks |
Check values for engine oil pressure
Number | Designation | Engines | ||
BE18.00-N-1001-01C | Engine oil pressure at | Idling speed | bar | 0.5 |
maximum speed | bar | 2.5 | ||
Oil pan
Number | Designation | Engines | ||
BA01.45-N-1001-01B | Screw/bolt, oil pan to cylinder crankcase | Nm | 25 | |
BA01.45-N-1002-01B | Oil drain screw to oil pan | M201.5 | Nm | 65 |
M261.5 | Nm | 85 | ||
Oil level sensor, oil pressure sensor
Number | Designation | Engines | |
BA18.40-N-1002-01C | Oil level sensor to oil pan | Nm | 50 |
Engine lubrication
Number | Designation | Engine 904.9 | Engine 904.9 | Engine | ||
BF18.00-N-1001-01C | Engine oil | Filling capacity with oil filter | l | 15.8 | 13.8 | 15.8 |
Specifications for Operating Fluids | Sheet | |||||
Sheet | ||||||
Sheet | ||||||
Sheet | ||||||
Sheet | ||||||
Engine lubrication
Number | Designation | Engine | Engine 906.9 | Engine 906.9 | ||
BF18.00-N-1001-01C | Engine oil | Filling capacity with oil filter | l | 29 | 29 | 27.5 |
Specifications for Operating Fluids | Sheet | |||||
Sheet | ||||||
Sheet | ||||||
Sheet | ||||||
Sheet | ||||||
Engine lubrication
Number | Designation | Engine 906.9 | Engine 906.9 | Engine 906.9 | ||
BF18.00-N-1001-01C | Engine oil | Filling capacity with oil filter | l | 29 | 29 | 27.5 |
Specifications for Operating Fluids | Sheet | |||||
Sheet | ||||||
Sheet | ||||||
Sheet | ||||||
Sheet | ||||||