Model | 213, 238 |
with code 641 (Dynamic LED headlamps, left-hand traffic) | |
except code 460 (Canada version) | |
except code 494 (US version) | |
except code 631 (Static LED headlamps, left-hand traffic) | |
except code 632 (Headlamps, LED, static, right-side traffic) | |
Model | 213, 238 |
with code 642 (Dynamic LED headlamps, right-hand traffic) | |
except code 460 (Canada version) | |
except code 494 (US version) | |
except code 631 (Static LED headlamps, left-hand traffic) | |
except code 632 (Headlamps, LED, static, right-side traffic) |
Shown on model 213 |
01 | Headlamp aimer |
E1 | Left front lamp unit |
P82.10-8083-12
Dynamic LED headlamp, ECE version, shown on model 213 |
E1 | Left front lamp unit |
E1e2 | Left low beam |
E1e24 | Left front adaptive high beam |
P82.10-8055-01
Light gradient for diagnostic light pattern |
1 | Light-dark boundary |
2 | Reference line for height adjustment |
3 | Central mark |
P82.10-8185-01
Shown on model 213 |
H | Height adjusting screw |
S | Side position adjusting screw |
P82.10-8100-01
Warning | Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear buttoned-up and snug-fitting work clothes. Do not touch hot or rotating parts. | |
General information on checking/correcting headlamp adjustment | |||
Preparatory activity | |||
1 | Prepare vehicle for checking/correcting headlamp adjustment | ||
2 | Determine degree of inclination for main headlamps | ||
Notes on determining headlamp aiming values | |||
The degree of inclination for the main headlamps is specified on the model plate on the B-pillar on the passenger side. | |||
3 | Set specified degree of inclination for main headlamps on headlamp aimer (01) | ||
| 000 588 11 21 00 Adjustment device | ||
4 | Switch on low beam | When testing and adjusting the low beams, make sure that the extended fog light function is not active. | |
Check and, if necessary, adjust (checking and adjustment of the low beams is described at the left low beam headlamp (E1e2); the same procedure is used for the right side.) | |||
5 | Check height adjustment of left low beam headlamp (E1e2); adjust if necessary | ||
| 000 588 11 21 00 Adjustment device | ||
When the diagnostic light pattern is switched on and the height adjustment is correct, the horizontal light-dark boundary (1) of the left low beam headlamp (E1e2) to the left of the center mark (3) must be congruent with the reference line for the height adjustment (2) in the headlamp aimer (01). | |||
If the height adjustment of the left low beam headlamp (E1e2) is correct with the diagnostic light pattern switched on. | |||
| |||
No further check necessary, continue with operation step 6. | |||
If the height adjustment of the left low beam headlamp (E1e2) is not correct with the diagnostic light pattern switched on. | |||
| |||
Turn the adjustment screw for the height adjustment (H) to correct the height adjustment of the left low beam headlamp (E1e2). | |||
6 | Check lateral adjustment of left low beam headlamp (E1e2); adjust if necessary | ||
| 000 588 11 21 00 Adjustment device | ||
When the diagnostic light pattern is switched on and the lateral adjustment is correct, the vertical light-dark boundary (1) of the left low beam headlamp (E1e2) each starting at the center mark (3) must run upward at 900 to the reference line for the height adjustment (2) in the headlamp aimer (01). | |||
If lateral adjustment of left low-beam headlamp (E1e2) is correct. | |||
| |||
No further check necessary, continue with operation step 7. | |||
If lateral adjustment of the left low beam headlamp (E1e2) is not correct. | |||
| |||
Turn the adjustment screw for the lateral adjustment (S) to correct the lateral adjustment of the left low beam headlamp (E1e2). | |||
Finishing activity | |||
7 | Reset switch positions to input condition | Only if the high beam setting is not to be checked afterwards. |