Shown on model 212.002 |
01 | Headlamp aimer |
S1 | Exterior lights switch |
S1s8 | Headlamp range controller |
P82.10-5800-01
P54.25-7945-01
| Check | ||
Warning | Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | |
Danger | Risk of death when working on component parts and systems with U >= 30 V alternating voltage (AC) or U >= 60 V direct voltage (DC) | Do not touch damaged or defective live component parts and lines or non-insulated electrical connections and lines. | |
Danger | Risk of explosion/risk of fire caused by highly flammable materials in the vicinity of damaged xenon bulbs. Risk of injury caused by UV light, hot components on xenon headlamps and glass splinters produced by bursting xenon bulbs. Risk of poisoning caused by inhalation of mercury vapors and by swallowing of/skin contact with toxic salts and mercury compounds. | Do not touch parts conducting high voltage. Persons with active electronic implants (e.g. cardiac pacemakers) must never work on xenon headlamps. Switch off the entire lighting system. Wear insulated safety shoes, safety glasses and protective gloves. Remove highly inflammable materials from the danger zone. Ensure sufficient ventilation in the working area. | |
1 | Park the vehicle on a horizontal, level surface | ||
2 | Put vehicle in ready-to-drive condition | Vehicle in ready-to-drive condition means: | |
3 | Open hood | Model 207, 212, 218 | |
| Model 207, 212 | ||
MODEL 207, 212 with CODE U60 (Pedestrian protection) | |||
4 | Prepare headlamp aimer (01) | ||
Notes on determining headlamp aiming values | |||
Align headlamp aimer (01) approx. 10 to max. 30 cm in front of the headlamps parallel to the vehicle at the height of the light source. Set specified headlamp inclination on scale of headlamp aimer (01). | |||
Commercially available devices/tools | |||
5 | Occupy driver seat with a person or load the seat with 75 kg | On vehicles with halogen headlamps and without level control system at front and rear axle | |
6 | Check fill level of fuel tank | On vehicles with halogen headlamps and without level control system at front and rear axle | |
If the fuel tank is not full, compensate for the missing weight by placing appropriate additional weights in the luggage compartment. | |||
7 | Switch on low beam at exterior lights switch (S1) | The turn signal lamps, rear fog lamp and Night View Assist must not be switched on! | |
8 | Check headlamp range control for proper function | ||
For vehicles with halogen headlamps, after completion of function test of headlamp range adjustment: | |||
| |||
Move headlamp range controller to 0 position. | |||
9 | Switch on ignition | ||
10 | Check low beam setting and adjust if necessary |
| |
Model 212, 218 | |||
On vehicles with xenon or LED headlamps: | |||
| |||
Conduct zero position adjustment of headlamp subject to separate repair order. | |||
11 | Check high beam adjustment | Model 207, 212, 218 | |
MODEL 207 | |||
MODEL 212 | |||
12 | Check fog lamp setting and adjust if necessary | Model 207, 212, 218 | |
ENGINE 207, 212 | |||
13 | Switch off lights and ignition | Put the vehicle back in its original condition. | |
14 | Adjust headlamp range adjuster (S1s8) to load condition | On vehicles with halogen headlamps | |
15 | Close engine hood | Model 207, 212, 218 | |
| Model 207, 212 | ||
MODEL 207, 212 with CODE U60 (Pedestrian protection) |