AN82.88-W-0001A | Retrofit toll system | 14.2.12 |
MODEL 950.0## /1## /2## /3##, 952.0## /1## /2## /3##, 953.1## /3##, 954.0## /1## /2## ## as of 472726
with CODE (F04) Cab L (long)
except CODE (DD1) Cab with 1400 mm floor-to-ceiling height (car transporter)
except CODE (DD2) Cab with 1550 mm floor-to-ceiling height
Grundig toll system in vehicles with MTCO tachograph
MODEL 950.0## /1## /2## /3##, 952.0## /1## /2## /3##, 953.1## /3##, 954.0## /1## /2## ## as of 472726 with CODE (F15) MEGASPACE cab
Grundig toll system in vehicles with MTCO tachograph
W82.88-1013-06
Shown on model 954 with
Code (F04) Cab L (long)
1 Multifunction antenna
2 On-board unit
(toll acquisition device)
3 DSRC communication module
W82.88-1034-05
Connection scheme
2 On-board unit
(toll acquisition device)
3 DSRC communication module
A7 Base module
A30 WS/FSS control unit
F2 Circuit 58 fuse
Fa Fuse toll system, term. 30
Fb Fuse toll system, term. 15
GPS GPS antenna
GSM GSM antenna
P1 MTCO tachograph
Modification notes
| Install | ||
1 | Install support battery in the on-board unit (toll acquisition device) (2) | ||
2 | Store vehicle and customer data with the service PC in the on-board unit (toll acquisition device) (2) | The procedure on the service PC can be obtained from the documents from the course "Installation of vehicle device" of the Toll Collect company. | |
3 | Open sliding roof | ||
4 | Switch off ignition | ||
Danger! | Risk of explosion caused by escaping oxyhydrogen gas. Risk of injury caused by caustic burns to eyes, skin and mucous membranes from battery electrolyte (contains diluted sulfuric acid) or metal spatter due to short circuit. Risk of burn injuries caused by short circuit. Risk of poisoning caused by swallowing battery electrolyte (contains diluted sulfuric acid) or absorption of lead over the skin or orifices | No fire, sparks, open flames or smoking. Wear acid-resistant gloves and clothing and safety glasses with side guards. Do not place any conductive objects on the battery and avoid any short circuit from battery positive to ground. Only fill liquid battery electrolyte (diluted sulfuric acid) into suitable and appropriately marked containers. | |
5 | Disconnect ground lead from battery | ||
| Notes on battery | ||
6 | Remove footwell trim on driver-side | ||
| |||
7 | Remove driver-side interior lamp | ||
8 | Remove MTCO modular tachograph (P1) | ||
| |||
9 | Remove covering on tachograph slot | ||
10 | Remove bracket for MTCO tachograph (P1) | ||
11 | Remove driver-side speaker | ||
12 | Remove paneling from A-pillar at driver side | The support rod must be reattached for the duration of the installation process after removing the paneling. | |
| |||
13 | Release Instrument (INS) and fold back | ||
| |||
14 | Open electrical compartment cover | ||
15 | Undo and fold back base module (A7). | ||
16 | Install multifunction antenna (1) | ||
| |||
17 | Install the extension lines for the multifunction antenna (1) | ||
18 | Install wiring harness for toll system | ||
19 | Connect wiring harness for toll system to MTCO modular tachograph (P1) | ||
20 | Connect wiring harness for toll system in electrical compartment | ||
21 | Connect and install DSRC communication module (3) | ||
| |||
22 | Prepare console housing for on-board-unit (toll acquisition device) (2) for installation and install | ||
23 | Adjust turn rate sensor (gyro) of On Board Unit (toll acquisition device) (2) | ||
| |||
24 | Connect and install On Board Unit (toll acquisition device) (2) | ||
25 | Install remaining parts onto vehicle | ||
26 | Synchronize MTCO modular tachograph (P1) | ||
27 | Check operation and carry out road test |
Antenna toll system
Number | Designation | Models 930 /932 /933 /934 /944 /950 /952 /953 /954 /970 /972 /974 /975 /976 | ||
BA82.88-N-1001-01A | Hirschmann multifunction antenna GPS 925/DCS on roof | Nm | 7 (1) | |
Choke angle gauge (electronic)
001 589 88 21 00
Parts ordering notes
Part no. | Designation | Quantity |
--- | Installation kit for Grundig toll system | 1 |
B6 782 1168 | Console for on-board unit | 1 |