1 | Rear spoiler on platform |
S60.30-0253-06
2 | Bolts |
3 | Electrical connector |
4 | Electrical wiring harness |
S60.30-0254-06
5 | Electrical wiring harness |
6 | Electrical wiring harness |
7 | Electrical connector |
S60.30-0255-06
8 | Front right of rear spoiler on platform |
S60.30-A005-12
Topical note | Notes on carrying out repair work in the vehicle interior | ||
General note on listed repair materials | |||
| Remove | ||
1 | Remove right trim in footwell. | ||
| |||
2 | Remove inside cover on dropside. | ||
| |||
3 | Remove left rear lamp unit. | ||
| |||
4.1 | Remove screw/bolts (2) . | Model 470 | |
Dispose of bolts (2). | |||
4.2 | Remove rear window protective grille. | Model 470 | |
| |||
Dispose of rear window protective grille. | |||
| Install | ||
5 | Retrofit platform inlay. | If platform inlay will be installed at the same time. | |
Do not install truckbed liner yet. | |||
6 | Make note of serial number (arrow). | The serial number (arrow) is located on the front right of the rear spoiler on platform (8). | |
7 | Prepare rear spoiler on platform (1) for installation. | ||
Topical note | General notes on touch-up applicators and paint spray cans | ||
Commercially available devices/tools | |||
Thread locking agent, Loctite 243 (10 ml) | |||
Cleaner | |||
Primer stick | |||
Bolt, cover on center piece in rear spoiler on platform | |||
Bolt, rear spoiler center section on platform to rear spoiler at front on platform | |||
Bolt, front rear spoiler on platform to rear spoiler at rear on platform | |||
Bolt, front rear spoiler on platform to rear spoiler at rear on platform | |||
8.1 | Install rear spoiler on platform (1). | Model 470 | |
Cleaner | |||
Nut to rear spoiler on platform on rear dropside | |||
Bolt, cover to rail on front rear spoiler on platform | |||
Bolt, fastening clamp for rear spoiler on platform | |||
Bolt, holder to rail on front rear spoiler on platform | |||
Bolt, bracket to dropside at side | |||
Bolt, holder to front dropside | |||
Stud bolt to rear spoiler on platform on dropside at rear | |||
8.2 | Install rear spoiler on platform (1). | Model 470 | |
Cleaner | |||
Bolt, fastening clamp for rear spoiler on platform | |||
Bolt, holder to rail on front rear spoiler on platform | |||
Bolt, bracket to dropside at side | |||
Bolt, holder to front dropside | |||
9 | Install electrical wiring harness (5) as shown. | To do so, connect the electrical wiring harness (5) of the installation kit with the electrical wiring harness (6) and wrap provided foam pads around connected electrical connector, as shown. | |
10 | Connect existing electrical connector of left rear lamp unit with electrical wiring harness (5). | ||
11 | Disconnect electrical connector (3) on right in footwell. | ||
12 | Install electrical wiring harness (4) as shown. | | |
Model 470 with engine 642 | |||
13 | Install trim in right footwell. | ||
| |||
14 | Install left rear lamp unit. | ||
| |||
Connect electrical connector (7). | |||
15 | Supplement cavity preservation for dropside. | Model 470 | |
| |||
16 | Install inner cover on dropside. | ||
| |||
17 | Retrofit truckbed liner. | If platform inlay will be installed at the same time. | |
18 | Enter special equipment with noted serial number in Vehicle Documentation (VeDoc). | To do so, record special equipment with noted serial number in VeDoc: | |
Designation of special equipment in question: Code Y1S (Roll bar (sports bar)). | |||
Attach note "Rear spoiler on platform retrofitted as per AN60.30-S-0011P" under field organization texts for DG 60. | |||
19 | Hand over General Operating Permit of rear spoiler on platform (1) to customer. | ||
| Service Information: Downloading the general operating permit for Mercedes-Benz Genuine Accessories | ||
If there is no General Operating Permit, it can be downloaded from the "ODUS" (XENTRY Portal) system and printed out. | |||
The retrofitted rear spoiler on platform (1) does not fulfill a protection function, but is designed exclusively as a design element. |