ar4610d7300a

Remove/install steering shaft

Тип ar · тема 46.10 · версия 0112 · 2011-10-18

Применимость: MODEL 901.0 /3 /4, 902.0 /3 /4, 903.0 /3 /4, 904.0 /3 /4

Нет на языке «ru»; показано на языке Английский.

Расположение

Функциональная группа 2 Ходовая часть › 46 Рулевое управление › 46.10 Рулевое колесо, трубчатая секция рулевой колонки, рулевой вал, замок блокировки рулевого вала — Серия 901 (модели 0**, 3**, 4**) · Серия 902 (модели 0**, 3**, 4**) · Серия 903 (модели 0**, 3**, 4**) · Серия 904 (модели 0**, 3**, 4**)

EinPAS 22 Рулевое управление › 22.15 Гидроусилитель рулевого управления › 22.15.40 Рулевое колесо/ рулевая колонка / трубчатая секция рулевой колонки / замок блокировки рулевого вала — Серия 901 (модели 0**, 3**, 4**) · Серия 902 (модели 0**, 3**, 4**) · Серия 903 (модели 0**, 3**, 4**) · Серия 904 (модели 0**, 3**, 4**)

AR46.10-D-7300A

Remove/install steering shaft

17.10.11

MODEL 901.0 /3 /4, 902.0 /3 /4, 903.0 /3 /4, 904.0 /3 /4

Remove/install steering shaft

D46.10-1117-06

1 Fitted bolt

2 U-joint

3 Shear bolt

4 Bolt

5 Bolts

Remove/install

Danger!

Risk of injury caused by performing testing or repair work on airbag or emergency tensioning retractor units.

Store airbag unit with deployment face up, do not subject to temperatures above 100 °C. When working on these units, disconnect the power supply.

AS91.00-Z-0001-01A

1

Disconnect ground cable from battery

2

Turn steering gear to center position and engage ignition lock

The position of the steering gear must not be altered again for the entire duration of the work procedure

AR46.20-D-0500-01A

3

Unscrew fitted bolt (1) on universal joint (2)

*000589011000

4

Detach universal joint from drive shaft

Installation: Install universal joint on drive shaft.

AR46.10-D-7300-01A

*000589011000

*BA46.10-N-1003-05C

5

Remove steering wheel

Except code SA5, Driver airbag.

AR46.10-D-0100A

With code SA5, Driver airbag.

AR46.10-D-0100B

6

Remove clock spring contact

With code SA5, Driver airbag.

AR46.10-D-0200A

Unscrew retaining bolts just enough to be able to remove the clock spring contact. Do not twist or disassemble the clock spring contact.

7

Remove central electric unit

AR54.25-D-1382B

8

Remove combination switch

AR54.25-D-2800A

9

Unhook pedal springs from clutch and brake pedal on steering column

For engine 601 unhook pedal spring only from clutch pedal.

10

Undo bolt (4) on steering column bracket

*BA46.10-N-1002-05C

11

Drill out shear-off screw (3) on steering column bracket

Installation: Tighten the bolt until it shears off.

12

Disconnect vacuum lines and electrical connector from ignition lock

Identify vacuum lines.

13

Pull out steering shaft

Installation: Slide steering shaft through cab floor. Check for correct seating in cab floor.

14

Install in the reverse order

Steering wheel, jacket tube, steering shaft

Number

Designation

Model
901, 902, 903, 904, 905

BA46.10-N-1002-05C

Jacket tube for steering shaft on belt rail

Nm

25

BA46.10-N-1003-05C

Universal joint to steering gear shaft

Nm

24

Remove/install steering shaft

000 589 01 10 00

Torx bit set

Связанные документы