ar0330p1600mt

Remove/install belt pulley/vibration damper

Tip ar · temă 03.30 · versiune 0201 · 2019-10-15

Valabil pentru: Engine 133 in model 117, 156, 176 Engine 270 in model 117, 156, 176, 242, 246 Engine 607 in model 117, 156, 176, 246

Nu este disponibil în „ro”; afișat în Engleză.

Încadrare

Grupă funcțională 1 Motor › 03 Mecanism de acţionare › 03.30 Volantă, disc antrenor, amortizor vibraţii, bendix — Seria 117 · Seria 156 · Seria 176 · Seria 242 · Seria 246

EinPAS 15 Motor › 15.15 Motor cu ardere internă complet/Carcasă motor/Mecanism bielă-manivelă › 15.15.41 Arbore cotit/Volantă/Flanșă de antrenare — Seria 117 · Seria 156 · Seria 176 · Seria 242 · Seria 246

EinPAS 15 Motor › 15.18 Antrenare curea › 15.18.30 Curea/Fulie de curea/Dispozitiv de întindere/Rolă de ghidare — Seria 117 · Seria 156 · Seria 176 · Seria 242 · Seria 246

Valabil și pentru motoare/cutii de viteze: 133 ***, 270 ***, 607 ***

AR03.30-P-1600MT

Remove/install belt pulley/vibration damper

14.10.2019

Engine

133 in model 117, 156, 176

Engine

270 in model 117, 156, 176, 242, 246

Engine

607 in model 117, 156, 176, 246

Remove/install belt pulley/vibration damper

Shown on engine 270

1

Center bolt

2

Belt pulley/vibration damper

3

Crankshaft

4

Groove

5

Radial shaft sealing ring

P03.30-2165-06

Remove/install

1

Switch off ignition and remove transmitter key

2

Remove poly-V belt


Engine 133 in model 117, 156, 176

AR13.20-P-0001MTA

Engine 607 in model 117, 156, 176, 246

AR13.20-P-0001ORA

Engine 270 in model 117, 156, 176, 242, 246.2

AR13.20-P-0001MT

3

Open service flap on fender liner in right front fender

4

Rotate engine at center bolt (1) to TDC

If necessary.

5

Install retaining lock for crankshaft/starter ring gear

AR03.30-P-5000NKB

6

Remove center bolt (1)

Installation: Install new center bolt (1).

Engine 133 in model 117, 156, 176
Engine 270 in model 117, 156, 176, 242, 246Central bolt, belt pulley / vibration damper to crankshaft

*BA03.30-P-1001-01S

Engine 607 in model 117, 156, 176, 246Central bolt of vibration damper

*BA03.30-P-1001-01T

7

Detach belt pulley/vibration damper (2) from crankshaft (3)

Installation: Place belt pulley/vibration damper (2) on crankshaft (3) and rotate to ensure that the feather key of the crankshaft (3) is engaged in the groove (4) on the belt pulley/vibration damper (2).

Check

8

Check contact surface of the radial shaft sealing ring (5) on the belt pulley/vibration damper (2) hub for scoring and galling

If there are problems:

Replace belt pulley/vibration damper (2).

9

Remove front radial shaft sealing ring (5).

Replace front radial shaft sealing ring (5) if necessary.

Engine 607 in model 117, 156, 176, 246

AR03.20-P-3000ORA

Engine 133 in model 117, 156, 176
Engine 270 in model 117, 156, 176, 242, 246.2

AR03.20-P-3000MT

10

Install in the reverse order

Check

Warning

Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running.

Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts.

AS00.00-Z-0005-01A

11

Perform an engine test run and check engine for leaktightness

Flywheel, drive plate, vibration damper, starter ring gear

Number

Designation

Engine 133

Engine 270

BA03.30-P-1001-01S

Central bolt, belt pulley / vibration damper to crankshaft

Stage 1

Nm

200

200

Stage 2

°

90

180

Flywheel, driven plate, vibration damper, starter ring gear

Number

Designation

Engine 607

BA03.30-P-1001-01T

Central bolt of vibration damper

Stage 1

Nm

120

Stage 2

°

95

Documente menționate