ar9160p0622c

Remove/install airbag/belt tensioner control unit

Typ ar · temat 91.60 · wersja 0101 · 2018-05-07

Dotyczy: Model 124 as of 9/1/87

Niedostępne w języku „pl”; wyświetlono w języku Angielski.

Umiejscowienie

Grupa funkcyjna 3 Nadwozie › 91 Fotele, leżanki, system zabezpieczenia pasażerów › 91.60 Poduszki powietrzne, system ochrony pieszych — Seria 124

EinPAS 27 Bezpieczeństwo bierne/ systemy zabezpieczające przed skutkami wypadków › 27.16 Poduszka powietrzna › 27.16.11 Moduł sterujący/ przekaźnik — Seria 124

EinPAS 27 Bezpieczeństwo bierne/ systemy zabezpieczające przed skutkami wypadków › 27.17 System zabezpieczający przed skutkami wypadków › 27.17.11 Moduł sterujący/ przekaźnik — Seria 124

AR91.60-P-0622C

Remove/install airbag/belt tensioner control unit

25.04.2018

Model

124 as of 9/1/87

Remove/install airbag/belt tensioner control unit

2

Screw

4

Carpet

6

Bolts

7

Bolts

8

Screw

9

Screw

P91.60-5007-06

Warning

Risk of injury during testing and repair operations related to pyrotechnical components

Do not expose pyrotechnical component parts to temperatures above 100 °C or 212 °F. Disconnect current supply when working on such component parts.

AS91.00-Z-0008-01A

Topical note

Information on preventing damage to electronic components due to electrostatic discharge

AH54.00-P-0001-01A

Information, assessment and legal requirements when working with, handling and storing pyrotechnical components

AH91.00-Z-0000-10A

Remove/install

1

Switch off ignition and remove ignition key

2

Disconnect battery ground line

3

Remove floor covering in front passenger footwell

4

Unscrew screw/bolt (2) from footrest at the front passenger footwell firewall

5

Extend footrest upwards and remove from front passenger footwell

6

Disconnect 10-pin electrical connector in front passenger footwell

7

Remove carpet (4) from center console

8

Remove screw/bolt (9)

9

Remove switch/selector lever cover

10

Unscrew screws/bolts (6) of ashtray

11

Disconnect electrical connectors and remove ashtray

12

Unscrew screw/bolt (8) of front passenger transmission tunnel lining

13

Disconnect electrical connector from airbag/emergency tensioning retractor control unit

14

Unscrew screws/bolts (7) from airbag/emergency tensioning retractor control unit

Bolt, control unit to vehicle floor

*BA91.60-P-1004-01P

15

Remove airbag/emergency tensioning retractor control unit

16

Install in the reverse order

Check

Warning

Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running.

Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts.

AS00.00-Z-0005-01A

17

Start engine, SRS/RS indicator lamp must go off after approx. 4 s

SRS/RS indicator lamp does not go off after approx. 4 s.

Run airbag test program.

18

Read out fault memory with pulse counter

AR91.60-P-0622-02A

Pulse counter

*124589192100

Airbag

Number

Designation

Model 124

BA91.60-P-1004-01P

Bolt, control unit to vehicle floor

Nm

10

Remove/install airbag/belt tensioner control unit

124 589 19 21 00

Pulse counter

Powiązane dokumenty