Remove/install front bumper

AR88.20-P-2000RG

Remove/install front bumper

08.03.2017

Model

190

Shown on model 190.3 except code M030 (GT R version)

1

Bumper

2

Bolts

3

Fender liner

4

Screw

X26/27

Front bumper parking system electrical connector

Shown on model 190.3 except code M030 (GT R version)

1

Bumper

6

Bolts

5

Screw

Shown on model 190 with code M030 (GT R version)

2

Bolts

5

Bolts

6

Bolts

X26/27

Front bumper parking system electrical connector

 Warning

Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof.

No parts of the body or limbs should be within the operating area when the components are moving.

AS00.00-Z-0011-01A

 Danger

Risk of death caused by vehicle slipping or toppling off of the lifting platform.

Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer.

AS00.00-Z-0010-01A

Topical note

Notes on working in engine compartment

AH60.00-P-0042-01RG

Topical note

General information on the impact absorber

AH88.20-P-1000-01A

Topical note

Notes on preventing damage to electronic components due to a magnetic tool

AH54.00-P-0002-01A

Topical note

Information on preventing damage to electronic components due to electrostatic discharge

AH54.00-P-0001-01A

 

Remove/install

1

Open engine hood and raise to vertical position

AR88.40-P-1000RG

2

Remove lower engine compartment paneling

AR61.20-P-1105RG

 Only remove front section.

3

Unlock electrical connector from front bumper parking system (X26/27) and disconnect

4

Detach front section of fender liner (3) in front fender

AR88.10-P-1300RG

 Loosen only until bolts (2) are accessible.

5

Unscrew bolts (2) on left and right side of vehicle

6

Unscrew bolts (5) on left and right side of vehicle

7

Remove bolts (6)

8

Guide front bumper (1) out of left and right side bracket and remove

 Helper required.

9

Install in the reverse order



Check

10

Check gap dimensions

AR60.00-P-0700-01RG

Gap dimension, fender to bumper lamp unit

*BE60.00-P-1005-01EA

Gap dimension, lamp unit to bumper

*BE60.00-P-1004-01EA

Gap dimension, engine hood to bumper

*BE60.00-P-1001-01EA

 Feeler gauge

*129589032100

If complaint present



Adjust bumper (1).

AR88.20-P-2001RG

Gap dimensions

Number

Designation

Model 190.3

Model 190.4

BE60.00-P-1001-01EA

Gap dimension, engine hood to bumper

Dimension "A"

mm

3,5 (0,5)

3,5 (0,5)

See

AR60.00-P-0700-01RG

AR60.00-P-0700-01RG

Gap dimensions

Number

Designation

Model 190.3

Model 190.4

BE60.00-P-1004-01EA

Gap dimension, lamp unit to bumper

Dimension "D"

mm

2,5 (1)

2,5 (0,5)

See

AR60.00-P-0700-01RG

AR60.00-P-0700-01RG

Gap dimensions

Number

Designation

Model 190.3

Model 190.4

BE60.00-P-1005-01EA

Gap dimension, fender to bumper lamp unit

Dimension "E"

mm

0 (+0,5)

0 (+0,5)

See

AR60.00-P-0700-01RG

AR60.00-P-0700-01RG