Remove/install front bumper · ar8820p2000rg · Mercedes-Benz WIS

AR88.20-P-2000RG

Remove/install front bumper

08.03.2017

Model

190

Shown on model 190.3 except code M030 (GT R version)

1	Bumper
2	Bolts
3	Fender liner
4	Screw
X26/27	Front bumper parking system electrical connector

P88.20-4544-06

P88.20-4545-08

Shown on model 190.3 except code M030 (GT R version)

1	Bumper		6	Bolts
5	Screw

Shown on model 190 with code M030 (GT R version)

2	Bolts
5	Bolts
6	Bolts
X26/27	Front bumper parking system electrical connector

P88.20-4717-06

 Warning	Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof.	No parts of the body or limbs should be within the operating area when the components are moving.	AS00.00-Z-0011-01A
 Danger	Risk of death caused by vehicle slipping or toppling off of the lifting platform.	Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer.	AS00.00-Z-0010-01A
Topical note	Notes on working in engine compartment		AH60.00-P-0042-01RG
Topical note	General information on the impact absorber		AH88.20-P-1000-01A
Topical note	Notes on preventing damage to electronic components due to a magnetic tool		AH54.00-P-0002-01A
Topical note	Information on preventing damage to electronic components due to electrostatic discharge		AH54.00-P-0001-01A
 	Remove/install
1	Open engine hood and raise to vertical position		AR88.40-P-1000RG
2	Remove lower engine compartment paneling		AR61.20-P-1105RG
		 Only remove front section.
3	Unlock electrical connector from front bumper parking system (X26/27) and disconnect
4	Detach front section of fender liner (3) in front fender		AR88.10-P-1300RG
		 Loosen only until bolts (2) are accessible.
5	Unscrew bolts (2) on left and right side of vehicle
6	Unscrew bolts (5) on left and right side of vehicle
7	Remove bolts (6)
8	Guide front bumper (1) out of left and right side bracket and remove	 Helper required.
9	Install in the reverse order
	Check
10	Check gap dimensions		AR60.00-P-0700-01RG
		Gap dimension, fender to bumper lamp unit	*BE60.00-P-1005-01EA
		Gap dimension, lamp unit to bumper	*BE60.00-P-1004-01EA
		Gap dimension, engine hood to bumper	*BE60.00-P-1001-01EA
		 Feeler gauge	*129589032100
		If complaint present
		
		Adjust bumper (1).
			AR88.20-P-2001RG

Gap dimensions

Number	Designation			Model 190.3	Model 190.4
BE60.00-P-1001-01EA	Gap dimension, engine hood to bumper	Dimension "A"	mm	3,5 (0,5)	3,5 (0,5)
		See		AR60.00-P-0700-01RG	AR60.00-P-0700-01RG

Gap dimensions

Number	Designation			Model 190.3	Model 190.4
BE60.00-P-1004-01EA	Gap dimension, lamp unit to bumper	Dimension "D"	mm	2,5 (1)	2,5 (0,5)
		See		AR60.00-P-0700-01RG	AR60.00-P-0700-01RG

Gap dimensions

Number	Designation			Model 190.3	Model 190.4
BE60.00-P-1005-01EA	Gap dimension, fender to bumper lamp unit	Dimension "E"	mm	0 (+0,5)	0 (+0,5)
		See		AR60.00-P-0700-01RG	AR60.00-P-0700-01RG

129 589 03 21 00

Feeler gauge

Referenced documents

ah5400p000101a Information on preventing damage to electronic components due to electrostatic discharge
ah5400p000201a Notes on preventing damage to electronic components due to a magnetic tool
ah6000p004201rg Notes on working in engine compartment
ah8820p100001a General information on the impact absorber
ar6000p070001rg Gap dimensions on hoods, doors and lids
ar6120p1105rg Remove/install lower engine compartment lining
ar8810p1300rg Remove/install fender liner in front fender
ar8820p2001rg Adjust front bumper
ar8840p1000rg Opening engine hood, moving to upright position and closing
as0000z001001a Risk of death caused by vehicle slipping or toppling off of the lifting platform.
as0000z001101a Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof.