Adjust front bumper

AR88.20-P-2001RG

Adjust front bumper

25.04.2017

Model

190

Modification notes

19.04.2017

Document for model 190.4 supplemented

AR60.00-P-0700-01RG

19.04.2017

Special tool in operation step 1 added

129 589 03 21 00

19.04.2017

Method adapted

Operation steps 6, 10, 11, 12, 13 and 14.

Shown on model 190.3 except code M030 (GT R version)

1

Front bumper

6

Bolts

5

Screw

Shown on model 190 with code M030 (GT R version)

2

Bolts

5

Bolts

6

Bolts

 Warning

Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof.

No parts of the body or limbs should be within the operating area when the components are moving.

AS00.00-Z-0011-01A

Topical note

Notes on preventing damage to electronic components due to a magnetic tool

AH54.00-P-0002-01A



Check

1

Check gap dimensions

AR60.00-P-0700-01RG

Gap dimension, fender to bumper lamp unit

*BE60.00-P-1005-01EA

Gap dimension, lamp unit to bumper

*BE60.00-P-1004-01EA

Gap dimension, engine hood to bumper

*BE60.00-P-1001-01EA

 Feeler gauge

*129589032100

Adjustment of gap dimension of lamp unit to bumper or hood to bumper

2

Open engine hood

AR88.40-P-1000RG

3

Release screws (5, 6) until front bumper (1) can be moved

4

Close engine hood

5

Adjust gap dimension between front bumper (1) and engine hood

Gap dimension, engine hood to bumper

*BE60.00-P-1001-01EA

 Feeler gauge

*129589032100

6

Adjust gap dimension of lamp unit to front bumper (1)

Gap dimension, lamp unit to bumper

*BE60.00-P-1004-01EA

 Feeler gauge

*129589032100

7

Open engine hood

 Helper required.

8

Tighten screw/bolts (5, 6)

9

Close engine hood

Adjustment of gap dimension of fender to bumper lamp unit

10

Release front section of fender liner in front fender until screws (2) can be accessed

AR88.10-P-1300RG

11

Loosen screw/bolts (2)

12

Adjust gap dimension of fender to bumper lamp unit

Gap dimension, fender to bumper lamp unit

*BE60.00-P-1005-01EA

 Feeler gauge

*129589032100

13

Tighten screws/bolts (2)

14

Install front section of fender liner in fender

AR88.10-P-1300RG

Gap dimensions

Number

Designation

Model 190.3

Model 190.4

BE60.00-P-1001-01EA

Gap dimension, engine hood to bumper

Dimension "A"

mm

3,5 (0,5)

3,5 (0,5)

See

AR60.00-P-0700-01RG

AR60.00-P-0700-01RG

Gap dimensions

Number

Designation

Model 190.3

Model 190.4

BE60.00-P-1004-01EA

Gap dimension, lamp unit to bumper

Dimension "D"

mm

2,5 (1)

2,5 (0,5)

See

AR60.00-P-0700-01RG

AR60.00-P-0700-01RG

Gap dimensions

Number

Designation

Model 190.3

Model 190.4

BE60.00-P-1005-01EA

Gap dimension, fender to bumper lamp unit

Dimension "E"

mm

0 (+0,5)

0 (+0,5)

See

AR60.00-P-0700-01RG

AR60.00-P-0700-01RG