D49.20-A033-79
Shown on engine 654.9 with code MP6 (Engine version Euro VI |
1 | Diesel oxidation catalytic converter | 5 | Electrical connector | 9 | Clip | ||
2 | NOXsensor with control unit | 6 | Electrical wiring harness | 10 | Clip | ||
3 | Exhaust temperature sensor | 7 | Bolts | 11 | Heat shield | ||
4 | Diesel particulate filter | 8 | Bolts | 12 | Turbocharger |
D49.20-A034-79
1 | Diesel oxidation catalytic converter | 10 | Clip | 13 | Seal | ||
8 | Bolts | 12 | Turbocharger | 14 | Seal | ||
9 | Clip |
Warning | Risk of burn injuries, suffocation and poisoning when working on the exhaust system and the components connected to it. Risk of suffocation and risk of poisoning caused by inhalation of gaseous and solid components of the exhaust. Risk of poisoning caused by skin contact with solid components of the exhaust. | Wear protective clothing and safety glasses. Use the extraction system. Move people out of the hazard area. | |
Caution | Risk of injury caused by scraping or cutting body parts on sharp vehicle parts | Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. | |
Topical note | Notes on self-locking nuts and bolts | ||
Topical note | Notes on avoiding damage through contamination and foreign objects | ||
| Remove | ||
1 | Remove engine cover. | ||
2.1 | Remove NOx sensor with control unit (2). | Engine 654.9 in model 907.1/2/6 | |
2.2 | Remove oxygen sensor. | Engine 654.9 in model 907.1/2/6 | |
3 | Remove exhaust gas temperature sensor (3) from the diesel oxidation catalytic converter (1) and place to one side. | ||
4 | Remove exhaust gas temperature sensor from the diesel particulate filter (4) and place to one side. | ||
5 | Remove AdBlue® metering valve from the diesel oxidation catalytic converter (1) and tie to one side with connected lines. | Engine 654.9 in model 907.1/2/6 | |
6 | Release and disconnect the electrical connector (5). | ||
7 | Expose electrical wiring harness (6) and bring out of the working area. | ||
8 | Remove screws_(7). | ||
9 | Remove screws (8). | ||
10 | Unscrew the screw on the clamp (9) and open the clamp (9). | The screw is secured on the clamp (9). | |
11 | Remove clamp (10). | ||
12 | Remove diesel oxidation catalytic converter (1) upward. | WIS Service Media | |
13 | Remove clamp (9) from the diesel oxidation catalytic converter (1). | If the diesel oxidation catalytic converter (1) is re-used. | |
14 | Remove seal (13) from the diesel oxidation catalytic converter (1). | If the diesel oxidation catalytic converter (1) is re-used. | |
15 | Remove seal (14) from the exhaust gas turbocharger (12). | ||
16 | Remove heat shield (11) from the diesel oxidation catalytic converter (1). | If the diesel oxidation catalytic converter (1) is being replaced. | |
| Clean | ||
17 | Clean the connecting points on the diesel oxidation catalytic converter (1). | If the diesel oxidation catalytic converter (1) is re-used. | |
Assembly cleaner | |||
18 | Clean separating points on the exhaust gas turbocharger (12) and on the diesel particulate filter (4). | Assembly cleaner | |
19 | Seal openings on the diesel oxidation catalytic converter (1) with protective covers. | If the diesel oxidation catalytic converter (1) is re-used. | |
Set of protective covers | |||
20 | Seal openings on the diesel particulate filter (4) and on the exhaust gas turbocharger (12) with protective covers. | Set of protective covers | |
| Install | ||
21 | Attach heat shield (11) from the diesel oxidation catalytic converter (1). | If the diesel oxidation catalytic converter (1) has been replaced. | |
22 | Remove protective covers from the diesel oxidation catalytic converter (1). | If the diesel oxidation catalytic converter (1) was reused. | |
23 | Remove protective covers from the diesel particulate filter (4) and from the exhaust gas turbocharger (12). | ||
24 | Attach new seal (14) from exhaust gas turbocharger (12). | ||
25 | Attach new seal (13) to the diesel oxidation catalytic converter (1). | ||
26 | Position new clamp (9) on the diesel oxidation catalytic converter (1). | ||
27 | Insert diesel oxidation catalytic converter (1) and position in the installation position. | ||
28 | Tighten screws (8) slightly by hand. | ||
29 | Tighten screws (7) slightly by hand. | ||
30 | Tighten new clamp (9). | Clamp to diesel oxidation catalytic converter and diesel particulate filter | |
31 | Position a new screw in the new clamp (10) and tighten it. | Ensure that the installation position of the clamp (10) is correct. | |
Clamp to diesel oxidation catalytic converter and turbocharger | |||
32 | Tighten screws (8). | Screw, diesel particulate filter to diesel oxidation catalytic converter | |
33 | Tighten bolts (7). | Screw, diesel oxidation catalytic converter to bracket | |
34 | Route electrical wiring harness (6) and connect and lock electrical connector (5). | ||
35 | Attach AdBlue® metering valve to the diesel oxidation catalytic converter (1). | Engine 654.9 in model 907.1/2/6 | |
36 | Attach exhaust gas temperature sensor to the diesel particulate filter (4). | ||
37 | Attach exhaust gas temperature sensor (3) to the diesel oxidation catalytic converter (1). | ||
38.1 | Install NOx sensor with control unit (2). | Engine 654.9 in model 907.1/2/6 | |
38.2 | Install lambda sensor. | Engine 654.9 in model 907.1/2/6 | |
39 | Install engine cover. | ||
| Check | ||
40 | Read out and delete fault memory. | ||
| |||
Warning | Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | |
41 | Carry out engine test run and check leak tightness of diesel oxidation catalytic converter (1). |
001 589 03 91 00
Set of protective covers
Powiązane dokumenty
- ad0000d200006ts
- ah0000n000101a Wskazówki dotyczące samozabezpieczających śrub i nakrętek
- ah0000p500001a Wskazówki dotyczące zapobiegania uszkodzeniom na skutek zabrudzeń i ciał obcych
- ar0110d2405tsm
- ar0704d0086tsm
- ar4920d0031tsm
- ar4920d1505tsm
- ar4920d2061tsm
- as0000z000501a Niebezpieczeństwo wypadku na skutek samoczynnego ruszenia przy pracującym silniku. Niebezpieczeństwo obrażeń na skutek zmiażdżenia lub poparzenia przy wykonywaniu czynności podczas rozruchu lub przy pracującym silniku.
- as0000z001701a Niebezpieczeństwo obrażeńo elementy pojazdu o ostrych krawędziach.
- as4900z000101a Niebezpieczeństwo poparzenia, uduszenia i zatrucia podczas prac przy układzie wydechowym i połączonych z nim elementach. Niebezpieczeństwo uduszenia i zatrucia przez wdychanie gazowych i stałych składników spalin. Niebezpieczeństw