ar0330p8001mfd

Remove/install flywheel / drive plate

Typ ar · temat 03.30 · wersja 0102 · 2020-04-09

Dotyczy: Engine 282 in model 118, 177, 247 with transmission 700.42

Niedostępne w języku „pl”; wyświetlono w języku Angielski.

Umiejscowienie

Grupa funkcyjna 1 Silnik › 03 Zespół napędowy › 03.30 Koło zamachowe, tarcza zabieraka, tłumik drgań, wieniec zębaty rozrusznika — Seria 118 · Seria 177 · Seria 247

EinPAS 15 Silnik › 15.15 Silnik spalinowy kompletny/obudowa silnika/mechanizm korbowy › 15.15.41 Wał korbowy/ koło zamachowe/ tarcza sprzęgła — Seria 118 · Seria 177 · Seria 247

Dotyczy też silników/skrzyń biegów: 282 ***, 700 42*

AR03.30-P-8001MFD

Remove/install flywheel / drive plate

24.03.2020

Engine

282 in model 118, 177, 247 with transmission 700.42

Remove/install flywheel / drive plate

1

Screw

2

Screw

3

Screw

4

Screw

5

Screw

6

Screw

7

Flywheel / drive plate

P03.30-2238-12

Caution

Risk of injury caused by scraping or cutting body parts on sharp vehicle parts

Always wear protective gloves when working on or near sharp and non-deburred vehicle parts.
Deburr repair panels.

AS00.00-Z-0017-01A

Topical note

Notes on avoiding damage through contamination and foreign objects

AH00.00-P-5000-01A

Topical note

Notes on self-locking nuts and bolts

AH00.00-N-0001-01A

Remove

1

Remove transmission.

AR27.10-P-0009MFD

2

Install retaining lock for crankshaft / starter ring gear.

AR03.30-P-5000MFD

3

Loosen screws (1 to 6).


To loosen the screws (1 to 6), do not use an impact wrench or similar compressed air tools.
Failure to observe will cause damage to the thread in the crankshaft flange.

4

Remove screws (1 to 6) and remove flywheel/drive plate (7).

Aid of helper required.

5

Check rear radial shaft sealing ring for leak tightness and damage.

If problems exist,

Replace rear radial shaft sealing ring.


AR03.20-P-3003MFD

Install

6

Position flywheel/drive plate (7) on crankshaft.

Aid of helper required.

The dowel pin of the crankshaft determines the installation position of the flywheel/drive plate (7).

7

Tighten screws (1 to 6) slightly by hand and screw tight as per the illustration in the numerical sequence.

Topical note

Notes on threaded connections fastened using a tightening angle-based tightening process

AH00.00-P-0020-01A

Bolt, starter ring gear/ drive plate to crankshaft

*BA03.30-P-1002-01ZA

8

Remove retaining lock for crankshaft/starter ring gear.

AR03.30-P-5000MFD

9

Install transmission.

AR27.10-P-0009MFD

Flywheel, drive plate, vibration damper, starter ring gear

Number

Designation

Engine 282

BA03.30-P-1002-01ZA

Bolt, starter ring gear/ drive plate to crankshaft

Stage 1

Nm

45

Stage 2

°

90

Powiązane dokumenty