Retrofit BRABUS light alloy wheels · an4010p0002mcu · Mercedes-Benz WIS

AN40.10-P-0002MCU

Retrofit BRABUS light alloy wheels

6.12.11

MODEL 451.3 /4 (except 451.391 /491) up to 19.3.12
with CODE (I01) Air conditioning Plus
with CODE (V26) Power steering, EPS (FFO)

P40.10-5292-04

1 BRABUS top part

Dimensions:

a 300 mm

b 18 mm

P40.10-5597-06

1 BRABUS top part

2 Rear CBS

3 BRABUS light alloy wheel

4 Fender liner

	Removing
1	Remove wheels		AR40.10-P-1100MCU
	Install
		 Retrofitting BRABUS (3) light alloy wheels is only permitted when the BRABUS parts listed in the following have been installed.
2	Retrofit BRABUS muffler		AN49.10-P-1003MCU
3	Retrofit BRABUS rear apron		AN88.20-P-0001MCU
4	Retrofit BRABUS front spoiler		AN88.50-P-0004MCC
5	Install side skirts, Brabus		AN88.80-P-0010MCC
6	Install Brabus sport suspension		AN32.20-P-0002MCC
7	Mount tire on BRABUS rim	 The valve, sleeve, sealing ring and nut are available in a repair kit and should always be replaced.	AR40.10-P-1030MCU
8	Install BRABUS light alloy wheels (3)		AR40.10-P-1100MCU
9	Mark the cut edge (arrow A) corresponding to dimensions (a and b) on BRABUS top part (1)	 Starting from the first attachment point (arrow B) dimension (a) is measured on the BRABUS top part (1) to the rear. Round off the cut edge (arrow A) slightly in the area of the corners.
 Danger!	Risk of injury caused by scraping or cutting body parts on sharp vehicle parts	Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. Deburr repair panels.	AS00.00-Z-0017-01A
 Danger!	Risk of injury caused by slipping when inserting blade in the multicutter and by glass splinters when cutting out bonded windows	Always interrupt air supply or power supply before inserting or removing blade. Wear protective gloves and safety glasses.	AS67.00-Z-0001-01A
10	Cut out the cutout along the cut edge (arrow A)	 Do not grind down the primer for the BRABUS attachment part (1). Otherwise the BRABUS attachment part (1) will have to be replaced.
		 Deburr cut edge (arrow A) with abrasive paper.
		Window glazing device, FSC 1.6 gotis://K_67.0_01.0
11	Position the BRABUS top part (1) on the CBS rear end (2) and align
12	Transfer the cutout made in the BRABUS attachment part (1) to the CBS rear end (2)
13	Remove BRABUS top part (1) from the CBS rear end (2)
 Danger!	Risk of injury caused by scraping or cutting body parts on sharp vehicle parts	Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. Deburr repair panels.	AS00.00-Z-0017-01A
 Danger!	Risk of injury caused by slipping when inserting blade in the multicutter and by glass splinters when cutting out bonded windows	Always interrupt air supply or power supply before inserting or removing blade. Wear protective gloves and safety glasses.	AS67.00-Z-0001-01A
14	Cut out the cutout along the marking (arrow C) on the CBS rear end (2)	 Do not damage the fender liner (4). Otherwise it must be replaced.
		Window glazing device, FSC 1.6 gotis://K_67.0_01.0
15	Install BRABUS top parts (1) on CBS rear end (2)		AN88.10-P-0006MCC
16	Attach information label on BRABUS tire pressure to the right B-pillar

Parts ordering notes

Part no.	Designation	Quantity
DG 58 (see EPC)	Information label on BRABUS tire pressure	1
DG 98 (see EPC)	Rear fender flares	1
DG 40 (see EPC)	BRABUS disk wheel	4

Powiązane dokumenty

an3220p0002mcc Montaż zawieszenia sportowego Brabus
an4910p1003mcu
an8810p0006mcc
an8820p0001mcu
an8850p0004mcc
an8880p0010mcc
ar4010p1030mcu
ar4010p1100mcu
as0000z001701a Niebezpieczeństwo obrażeńo elementy pojazdu o ostrych krawędziach.
as6700z000101a Niebezpieczeństwo obrażeń wskutek ześlizgnięcia się noża podczas mocowania w wielofunkcyjnym przyrządzie do cięcia i przez odpryski szkła podczas wycinania wklejanych szyb.