P49.10-2586-09
Shown on 251.175
1 Center muffler
2 Bolts
3 Hose clamp
4 Exhaust rubber mount in the middle
5 Hose clamps
6 Sealing ring
7 Right catalytic converter
8 Flange
9 Bolts
| Remove/install | ||
Danger! | Risk of death caused by vehicle slipping or toppling off the lifting platform. | Align vehicle between columns of vehicle lift and position four support plates at vehicle lift support points specified by vehicle manufacturer. | |
Danger! | Risk of injury to skin and eyes caused by handling hot or glowing objects. | Wear safety gloves, protective clothing and safety glasses, if necessary. | |
Danger! | Risk of injury caused by scraping or cutting body parts on sharp vehicle parts | Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. Deburr repair panels. | |
| Notes on self-locking nuts and bolts | ||
| When working on exhaust system, connecting points have to be cleaned from combustion and corrosion residues before the installation of parts. Install new sealing ring (6) as well as bolts and nuts | ||
1 | Remove nuts as well as bolts (2) from flange connection | Installation: Ensure that sealing ring (6) and flange (8) are seated correctly. | |
| |||
2 | Release clamp (3) | Slide released hose clamp toward front onto left catalytic converter. Replace defective or corroded hose clamp. | |
| |||
3 | Support exhaust system under the center muffler (1) | Use a suitable transmission jack. | |
4 | Unscrew bolts (9) from center exhaust rubber mount (4) | | |
5 | Loosen hose clamps (5) | Slide released hose clamp towards rear onto the left rear muffler or the right rear muffler. Replace defective or corroded hose clamps. | |
| |||
6 | Remove center muffler (1) | Slide center muffler towards rear until the center muffler detaches from the pipe of the right catalytic converter (7). Then remove it downwards. | |
Do not damage any surrounding components. | |||
Installation: Ensure that installation position of sealing ring (6) and flange (8) is correct. The chamfer of the sealing ring as well as shoulder on the flange are pointing in the direction of the center muffler. Slide both parts onto right catalytic converter before center muffler is positioned. | |||
| Checking | ||
7 | Check center exhaust rubber mount (4), hose clamp (3), hose clamps (5) as well as flange (8) | Check for damage and wear; replace if necessary. | |
8 | Install in the reverse order | ||
| Checking | ||
9 | Check installation position and for unobstructed movement of entire exhaust system | The exhaust system must be mounted free of tension, align exhaust system if required. | |
Danger! | Risk of accident caused by vehicle starting off by itself when engine is running. Risk of injury caused by contusions and burns during starting procedure or when working near the engine as it is running | Secure vehicle to prevent it from moving by itself. | |
10 | Conduct an engine test run and inspect exhaust system for leaks |
Exhaust system
Number | Designation | Engine 113 in model 251 | Engine | ||
BA49.10-P-1003-01X | Self-locking nut, rear muffler flange connection to three way catalytic converter | Nm | 20 | 20 | |
BA49.10-P-1005-01X | Bolt, hose clamp of rear muffler to center muffler | Nm | 35 | 35 | |
BA49.10-P-1018-01X | Bolt, rear muffler hose clamp to catalytic converter | Nm | 35 | 35 | |
BA49.10-P-1019-01X | Bolt, center exhaust rubber mount bracket (inner) to body | Nm | 18 | 18 | |
참조 문서
- ah0000n000101a 자가 잠금식 볼트와 너트 관련 지침
- as0000z000201a 뜨겁거나 달아오른 물체를 취급할 때 피부와 눈에 입을 수 있는 상해 위험
- as0000z000501a 엔진이 작동 중인 상태에서 급발진에 의한 사고 위험 시동 또는 구동 중인 엔진 근처에서 작업할 때 차량에 부딪히거나 열에 의한 상해 위험
- as0000z001001a 리프터에서 차량이 미끄러지거나 틸팅 시 생명의 위험
- as0000z001701a 모서리가 날카로운 차량 부품에서 절단상과 찰과상으로 인한 상해 위험