Measure propeller shaft alignment with electronic propeller shaft inclinometer

AR41.10-P-0086A

Measure propeller shaft alignment with electronic propeller shaft inclinometer

10.11.11



Measure



Notes on self-locking nuts and bolts

AH00.00-N-0001-01A



The vehicle must be on its wheels for the measurement.



The transmission mounts and exhaust system must not be stressed during the inclination angle measurement

 If necessary, relieve the stress in the transmission mounts/exhaust system.

To relieve the stress in the transmission mounts, loosen the left and right engine mount as well as the rear engine crossmember, align and tighten again.



Driveshaft bend angles that are outside the specified tolerance range can lead to reports of drivetrain vibration and rough response to acceleration

1.1

Drive the vehicle onto a suitable pit and secure using the parking brake or hand brake

1.2

Drive the vehicle onto a measuring car lift and secure using the parking brake and hand brake

2.1

Remove bottom section of soundproofing under the transmission

Model 210 with diesel engine

AR94.30-P-5300AB

2.2

Detach engine compartment paneling under the transmission

Model 208.365/370/374/465, model 210 with gasoline engine

AR61.20-P-1105AB

Model 208.34/44

Model 170

AR61.20-P-1105A

3

Prepare electronic propeller shaft inclinometer

AR41.10-P-0086-02P

Propeller shaft inclinometer

gotis://A_41/46/45_03.0

4

Check the driveshaft clinometer and adjust as required

 To check and adjust, see equipment operator's manual.

 The following measurement can be carried out using two different measuring instruments.

Propeller shaft inclinometer

gotis://A_41/46/45_03.0

5

Measure absolute angle at transmission

AR41.10-P-0085-01P

Propeller shaft inclinometer

gotis://A_41/46/45_03.0

6

Measure absolute angle at front and rear propeller shafts

AR41.10-P-0085-02P

Propeller shaft inclinometer

gotis://A_41/46/45_03.0

7

Measure absolute angle at rear axle housing

AR41.10-P-0085-03P

Propeller shaft inclinometer

gotis://A_41/46/45_03.0

8

Read out inclination angles (1) to (3) from memory of electronic driveshaft inclinometer and correct on the vehicle if necessary

 Perform any required removal and installation work if the inclination angle must be adjusted.

AR41.10-P-0086-01A



Data Sheet for Measuring Inclination Angle, Form

OF41.10-P-3000-01A

Propeller shaft inclinometer

gotis://A_41/46/45_03.0

Front inclination angle from transmission to front propeller shaft (1)

*BE41.10-P-1001-01A

Center inclination angle from front propeller shaft to rear propeller shaft (2)

*BE41.10-P-1002-01A

Rear inclination angle from rear propeller shaft to rear axle center assembly (3)

*BE41.10-P-1003-01A

 Carry out a check measurement again each time the inclination angle is corrected.

Number

Designation

Model
170

Model
208
with transmission
716

Model
210.0/2
with transmission
716

BE41.10-P-1001-01A

Front inclination angle from transmission to front propeller shaft (1)

°

-0.33° to +0.67°

-0.50°...+0.67°

-0.50°...+0.67°

BE41.10-P-1002-01A

Center inclination angle from front propeller shaft to rear propeller shaft (2)

°

+0.00°...+1.17°

+0.17° to +1.00°

+0.17° to +1.00°

BE41.10-P-1003-01A

Rear inclination angle from rear propeller shaft to rear axle center assembly (3)

°

-1.17°...-0.33°

-0.83°...-0.17°

-0.83°...-0.17°