1 Cap
2 Expansion reservoir
3 Coolant hose
4 Clamp
5 Radiator
P20.00-2346-03
Modification notes
Drain | |||
Danger! | Risk of injury to skin and eyes caused by scalding from contact with hot coolant spray. Risk of poisoning caused by swallowing coolant. | Do not open cooling system unless coolant temperature is below 90°C. Open cap slowly and release the pressure. Do not pour coolant into beverage containers. Wear protective gloves, protective clothing and safety glasses. | |
| Notes on coolant | ||
1 | Remove maintenance flap | ||
2 | Turn cooling system cap (1) on engine radiator (2) a half turn counterclockwise, relieve the pressure and then unscrew the cooling system cap (1) | ||
Danger! | Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between columns of vehicle lift and position four support plates at vehicle lift support points specified by vehicle manufacturer. | |
3 | Raise vehicle using the vehicle lift and remove underfloor paneling | Cordless drill/driver, cordless drill | |
4 | Loosen clamp (4) of coolant hose (3), detach coolant hose (3) from radiator (5) and drain coolant | Catch coolant in a suitable vessel. | |
Filling | |||
5 | Position coolant hose (3) on radiator (5) and fasten with clamp (4) | Replace hose clamp (4). | |
6 | Lower vehicle with vehicle lift | ||
7 | Pour in coolant and bleed cooling system | ||
| |||
| |||
| Coolant specifications | Sheet 310.1 | |
| Anticorrosion/antifreeze agents (Sheet 325.0) | Sheet 325.0 | |
8 | Seal expansion reservoir (2) with cap (1) | ||
| Checking | ||
Danger! | Risk of accident caused by vehicle starting off by itself when engine is running. Risk of injury caused by contusions and burns during starting procedure or when working near the engine as it is running | Secure vehicle to prevent it from moving by itself. | |
9 | Run engine until warm | Until the coolant fan motor cuts in. | |
10 | Turn cooling system cap (1) on engine radiator (2) a half turn counterclockwise, relieve the pressure and then unscrew the cooling system cap (1) | ||
11 | Check coolant level in the expansion reservoir (2) and correct if necessary | The engine coolant level in the coolant expansion reservoir (2) must be positioned at the max. marking. | |
| Coolant specifications | Sheet 310.1 | |
| Anticorrosion/antifreeze agents (Sheet 325.0) | Sheet 325.0 | |
12 | Seal expansion reservoir (2) with cap (1) | ||
13 | Raise vehicle with vehicle lift | ||
14 | Install underfloor paneling | ||
15 | Lower vehicle with vehicle lift | ||
16 | Install maintenance flap |
450 589 20 63 00
Filling device
Pressure pump
450 589 07 21 00
참조 문서
- ah2000n208001a 냉각수 지침
- ar2000p114206mcd
- as0000z000501a 엔진이 작동 중인 상태에서 급발진에 의한 사고 위험 시동 또는 구동 중인 엔진 근처에서 작업할 때 차량에 부딪히거나 열에 의한 상해 위험
- as0000z001001a 리프터에서 차량이 미끄러지거나 틸팅 시 생명의 위험
- as2000z000101a 뜨거운 냉각수 분출 시 입은 화상에 의한 피부와 안구의 상해 위험 냉각수의 음용으로 인한 중독 위험
- bb0040p031001a 냉각수에 관한 규정
- bb0040p032500a 부식 방지제/부동액(사양 325.0)