1 | Collar nut |
2 | Yoke coupling |
3 | Radial seal |
4 | Tapered roller bearing |
5 | Taper roller bearing outside race |
6 | Differential housing |
7 | Spacer washer |
8 | Spacer sleeve |
9 | Taper roller bearing outside race |
10 | Tapered roller bearing |
11 | Pinion |
B35.31-0038-02
1 | Collar nut |
3 | Radial seal |
5 | Taper roller bearing outside race |
6 | Differential housing |
9 | Tapered roller bearing outside race |
11 | Pinion |
B35.31-0035-02
B35.31-0034-02
| Remove | ||
1 | Remove the differential assembly |
| |
Caution | Risk of injury caused by scraping or cutting body parts on sharp vehicle parts | Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. | |
2 | Remove the crown with the differential assembly |
| |
3 | Unlock the collar nut (1) |
| |
4 | Immobilize the yoke coupling (2) and remove the nut with the collar (1) | Retainer wrench | |
Socket wrench bit | |||
5 | Remove the yoke coupling (2) | Puller | |
6 | Remove the pinion (11) | To remove the pinion (11), reinstall the collar nut (1) to protect the pinion thread. Tap the pinion shaft with the aid of a hammer and a brass billet until it is removed. | |
7 | Remove the radial seal (3) | ||
8 | Remove the differential housing (6), the tapered roller bearing (4), the spacer washer (7) and the spacer bushing (8) | ||
9 | Remove the outer races of the tapered roller bearings (5, 9) from the differential housing (6) | Use a hammer and a brass billet. | |
| Check | ||
10 | Check the tapered roller bearings (4, 10) for wear and damages |
| |
If needed, replace the tapered roller bearings (4, 10). | |||
| |||
Remove the tapered roller bearing (10) from the pinion. | |||
| Install | ||
11 | Install the tapered roller bearings (10) on the pinion (11) |
| |
Only in the case of replacing the tapered roller bearing (10). | |||
12 | Install the outer race of the tapered roller bearing (9) on the differential housing (6) and determine the basic depth of the pinion (11) |
| |
Rear axles 743.480 | |||
When installing the outer race of the tapered roller bearing (9) on the tapered roller bearing (10), it is necessary to define the drive pinion assembly measure (11). | |||
Warning | Risk of injury. Skin or eye injuries may result when handling hot or glowing objects. | Wear protective gloves, protective clothing and safety glasses, if necessary. | |
13 | Install the pinion (11), the outer race of the tapered roller bearing (5), the spacer bushing (8), the spacer washer (7) and the tapered roller bearing (4) on the differential housing (6) |
| |
Determine the spacer washer thickness (7) for the correct frictional torque of the pinion. | |||
To install the tapered roller bearing (4), heat it to approximately 80°C. | |||
14 | Install the radial seal (3) | Use a new radial seal. | |
Apply a sealing agent to the outer surface of the seal. | |||
Sealant | |||
Drift | |||
15 | Install the yoke coupling (2) | ||
16 | Install the collar nut (1) | .Nut on transmission shaft's flange | |
Socket wrench bit | |||
Retainer wrench | |||
17 | Lock the collar nut (1) |
| |
18 | Install the crown on the differential assembly |
| |
19 | Install the differential assembly |
|
744 589 00 15 00
Drift
000 589 12 09 00
Socket wrench bit
035 589 01 33 00
Puller
717 589 00 31 00
Retainer wrench
Documenti citati
- ar3530b043203ta
- ar3530b043205ta
- ar3530b0432d
- ar3530b045801e
- ar3530b045801f
- ar3530b0464f
- ar3530b047004e
- ar3530b430001b
- as0000z000201a Pericolo di lesioni alla pelle e agli occhi nel maneggiare oggetti caldi o incandescenti
- as0000z001701a Pericolo di lesioni a causa di tagli o abrasioni provocati dai bordi taglienti dei componenti del veicolo.