ar1820p3471ts

Remove/install oil filter housing

Tyyppi ar · aihe 18.20 · versio 0108 · 2009-07-23

Koskee: ENGINES 272, 273 in MODEL 211, 219

Ei saatavilla kielellä ”fi”; näytetään kielellä Englanti.

Sijainti

Toimintoryhmä 1 Moottori › 18 Moottorin voitelu, öljynjäähdytys › 18.20 Öljynsuodatin — Mallisarja 211 · Mallisarja 219

EinPAS 15 Moottori › 15.20 Moottorin voitelujärjestelmä › 15.20.31 Suodatin/jäähdytys/termostaatti/tuuletin/säiliö — Mallisarja 211 · Mallisarja 219

Koskee myös moottoreita/vaihteistoja: 272 ***, 273 ***

AR18.20-P-3471TS

Remove/install oil filter housing

20.7.09

ENGINES 272, 273 in MODEL 211, 219

Remove/install oil filter housing

P18.20-2053-08

1 Coolant hose

2 Coolant thermostat housing

5a Screw

5b Gasket

3 Poly-V belt tensioning device

4 Pulley

5 Oil filter housing

Remove/install oil filter housing

P20.20-2318-06

6 Coolant pipe

6a Coolant hoses

6b Bolts

7 Hose

8 Air shutoff valve

M33 Electric air pump

Remove/install

1

Remove bottom engine compartment paneling

Model 211

AR61.20-P-1105T

Model 219

AR61.20-P-1105TX

2

Drain coolant at radiator

AR20.00-P-1142TS

3

Remove front engine cover

Pull the front engine cover upward and out of the mountings.

4

Remove oil filter element from oil filter housing (5)

To empty the oil filter housing (5).

Replace oil filter element, drain oil filter

Model 211, 219 with engine 272

AP18.00-P-0101-06V

Model 211, 219 with engine 273

AP18.00-P-0101-06SX

5

Remove poly-V-belt and poly-V-belt tensioning device (3)

AR13.20-P-0001TS

6

Remove guide pulley (4) for poly-V-belt

7

Detach top coolant hose (1) from coolant thermostat housing (2) and place it on the side

Engine 272

Installation: Install new O-ring.

*BA20.10-P-1004-01U

8

Remove hose (7) from electrical air pump (M33) and air shutoff valve (8)

Engine 273

9

Remove coolant hoses (6a), unscrew bolts (6b) and remove coolant pipe (6)

Engine 273

*BA20.10-P-1005-01U

*BA20.10-P-1006-01U

10

Remove coolant thermostat housing (2)

*BA20.10-P-1003-01U

11

Remove bolts (5a)

Installation: Observe bolt order and tightening torques:

See bolt plan for oil filter housing

AR18.20-P-3471-01VA

12

Remove oil filter housing (5)

Catch dripping engine oil in a pan.

13

Replace seal (5b)

14

Install in the reverse order

Checking

15

Check engine oil level, correct if necessary.

Danger!

Risk of accident caused by vehicle starting off by itself when engine is running. Risk of injury caused by contusions and burns during starting procedure or when working near the engine as it is running

Secure vehicle to prevent it from moving by itself.
Wear closed and snug-fitting work clothes.
Do not touch hot or rotating parts.

AS00.00-Z-0005-01A

16

Conduct engine test run and check engine for leaks

Coolant pump, coolant thermostat

Number

Designation

Engine 272

Engine 273

BA20.10-P-1003-01U

Bolt, coolant thermostat housing to timing case cover

Nm

25

25

BA20.10-P-1004-01U

Bolt, guide pulley between water pump and belt tensioner

Initial installation

Nm

35

35

Follow-up operations

Nm

25

25

BA20.10-P-1005-01U

Bolt connecting coolant pipe to
coolant thermostat housing

Nm

-

9

BA20.10-P-1006-01U

Bolt connecting coolant pipe to cylinder head front cover

Nm

-

9

Viitatut asiakirjat