P72.20-2484-06
Shown on vehicle with Keyless Go, code 889 and automatic rear-end door, code 890
1 Cable for center high-mounted stop lamp
2 Washer fluid hose
3 Clips
4 Tie strap
W8/1 Ground (left rear-end door)
W8/2 Ground (right rear-end door)
P72.20-2485-06
5 Electrical connector
6 Electrical connector
7 Electrical connectors
A2/19 FM rear window antenna amplifier
E19/3 License plate lamp, left rear-end door
E19/4 License plate lamp, right rear-end door
M6/4 Rear-end door wiper motor
S62/21 Rear-end door Keyless Go button
S88/9 Rear-end door handle switch
W8 Ground (rear-end door)
P72.20-2486-06
8 Dust protection cover
9 Opening
10 Opening
11 Bolts
| Remove/Install | ||
Danger! | Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof. | When moving components, ensure that no body parts or limbs are within the operating range of moving parts. | |
1 | Switch off ignition and remove transmitter key from EIS control unit | On vehicles with Keyless Go, code 889: Press Keyless Go start/stop button repeatedly until ignition is switched off Remove transmitter key from vehicle and store it in a location beyond its transmission range (at least 2 m). | |
2 | Remove door lining on rear-end door | ||
3 | Remove rear-end door spray nozzle | ||
Mounting wedge | |||
4 | Unclip washer fluid hose (2) from clips (3) | ||
5 | Loosen nut on ground (left rear-end door) (W8/1) and ground (right rear-end door) (W8/2) | ||
6 | Remove center high-mounted stop lamp | ||
7 | Disconnect cable for center high-mounted stop lamp (1) from tie strap (4) | Installation: Install new tie straps. | |
8 | Loosen nut from ground (rear-end door) (W8) | ||
9 | Disconnect electrical connectors (7) from rear window heater | ||
10 | Disconnect electrical connector from FM rear window antenna amplifier (A2/19) | ||
11 | Disconnect electrical connector (5) from Keyless Go antenna | ||
12 | Disconnect electrical connector from rear-end door wiper motor (M6/4) | ||
13 | Disconnect electrical connectors from rear-end door handle switch (S88/9), rear-end door Keyless Go button (S62/21), left rear-end door license plate lamp (E19/3) and right rear-end door license plate lamp (E19/4) | ||
14 | Disconnect electrical connector (6) from rear-end door signal tone and rear-end door lock | ||
15 | Disconnect tie strap from entire wiring harness of rear-end door | Installation: Install new tie straps. Do not damage wiring harness | |
16 | Guide washer fluid hose (2) and wiring harness through left opening (2) | Ensure that rubber grommets are not damaged to prevent damage from water ingress | |
17 | Guide wiring harness through right opening (10) | Ensure that rubber grommets are not damaged to prevent damage from water ingress | |
18 | Unclip dust protection cover (8) and pull dust protection down on door hinge | ||
19 | Slacken bolts (11) | Support rear-end door with second mechanic Repair paint damage on screw heads with corresponding touch-up paint pen | |
| |||
20 | Remove rear-end door | Support rear-end door with second mechanic Install suitable protective layer between rear spoiler and roof to prevent damaging the paint. | |
21 | Install in the reverse order | ||
| Check | ||
22 | Check gaps on rear-end door all the way around | If necessary, adjust rear-end door, see: | |
Adjust rear-end door |
Rear-end door
Mounting wedge
110 589 03 59 00
Referenced documents
- ar7220p3510rt Adjust rear-end door
- ar7220p3520rt Remove/install rear-end door lining
- ar8210p5375rt Remove/install center high-mounted stop lamp
- ar8235p6920rt Remove/install tailgate spray nozzle
- as0000z001101a Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof.