129 589 03 21 00
Feeler gauge
The following operation steps are shown on the left side of the vehicle. In case of damage on the right side of the vehicle, these steps must be performed analogously.
The higher-level service document as well as the safety information in the service document must be observed.
1 | Install rear fender and fit. |
2 | Install rear bumper and fit. |
3 | Install trunk lid and fit. |
4 | Install and fit tail lamp. |
5 | Install seal and fit. |
6 | Install lock striker and fit. |
7 | Check gaps using feeler gauge and adjust. |
8 | Fix in place rear fender. |
9 | Remove striker eye. |
10 | Remove seal. |
11 | Remove taillamp. |
12 | Remove trunk lid. |
13 | Remove rear bumper. |
P63.50-3918-09
Shown on model 222.1 with code Z07 (Top protection) |
14 | Drill rivet holes on the rear fender (1) with a diameter of 6.7 mm (areas A2, B). |
Drill rivet holes from inside through present holes in body (area A2). |
15 | Drill rivet holes on the rear fender (1) with a diameter of 6.7 mm (areas A1, A3, A4, A5, A6). |
Only if no riveter for punching and flow-form rivets is used for installation. |
Drill rivet holes from inside through the existing holes in the body (areas A1, A3, A4, A5). |
Transfer position of present holes in body to new part (area A6). |
16 | Countersink rivet holes on the rear fender (1) (areas A4, A5, A6). |
17 | Remove rear fender (1). |
18 | Deburr rivet holes on rear fender (1) and body on both sides. |
19 | Remove drilling chips. |
20 | Coat insides of riveted joints with zinc dust paint (area B). |
P63.50-4040-09
Shown on model 222.1 with code Z07 (Top protection) |
21 | Attach suitable spacers to the rear outer wheel well at uniform intervals (area E). |
22 | Apply sealant to outer rear wheel well and foam parts (areas D1, E). |
23 | Apply 2-component adhesive to body in crosshatched areas (areas D2). |
Observe pretreatment of bonding surfaces and manufacturer's specifications for drying and processing time of 2-component adhesive. |
P63.50-3920-09
Shown on model 222.1 with code Z07 (Top protection) |
24 | Install rear fender (1), fit and fix in place. |
25 | Rivet rear fender (1) with rivets with a diameter of 6.4 x 12 (areas F1, F2, F3, F4, F5). |
Flow form rivet structure up to 3.5 mm clamping range (S1) can also be used if a riveter for punching and flow form rivets is used for installation (areas F2, F3, F4, F5). |
26 | Rivet rear fender (1) with countersunk-head rivets with a diameter of 6.4 x 14 (areas F6, F7, F8). |
Flow form rivet structure up to 3.5 mm clamping range (S1) can also be used if a riveter for punching and flow form rivets is used for installation. |
27 | Rear fender (1) (area H). |
28 | Arrest transitions at crimped edge for seals with vise grip pliers until the 2-component adhesive has cured. |
P63.50-4052-09
Shown on model 222.9 with code Z07 (Top protection) |
29 | Drill holes for plug welds on the rear fender (1) (areas T). |
P63.50-4053-09
Shown on model 222.9 with code Z07 (Top protection) |
30 | Rear fender (1) (areas T). |
31 | Rear fender (1) (areas L, O). |
Shown on model 222.9 with code Z07 (Top protection) |
P63.50-4042-06
32 | Model 222.1 |
Perform inert gas welding at intervals and allow to cool down in between. This reduces heat distortion. |
33 | Model 222.1 |
34 | Model 222.1 |
35 | Model 222.1 |
Shown on model 222.1 with code Z07 (Top protection) |
P63.50-3922-12
36 | Model 222.9 |
Perform inert gas welding at intervals and allow to cool down in between. This reduces heat distortion. |
37 | Model 222.9 |
38 | Model 222.9 |
39 | Model 222.9 |
Shown on model 222.9 with code Z07 (Top protection) |
P63.50-4009-05