Remove/install A-pillar outer section · ar6320s1102e · Mercedes-Benz WIS

AR63.20-S-1102E

Remove/install A-pillar outer section

10.09.2020

Model

447, 448

Shown on right side of vehicle

1	A-pillar outer section
4	Door hinge strap

S63.20-A000-06

 Danger	Risk of death when working on component parts and systems with U >= 30 V alternating voltage (AC) or U >= 60 V direct voltage (DC)	Do not touch damaged or defective live component parts and lines or non-insulated electrical connections and lines.Model 447 with engine 780	AS00.00-Z-0035-01A
 Danger	Risk of death caused by vehicle slipping or toppling off of the lifting platform.	Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer.	AS00.00-Z-0010-01A
 Danger	The high voltage used for electric welding presents a lethal hazard. Risk of explosion from welding in areas close to highly inflammable materials. Risk of injury from weld splatter and UV-light when welding. Risk of poisoning from inhaling welding gases	Use insulating mats. Wear protective clothing, safety glasses and a protective mask. Remove highly inflammable materials from the hazard area. Use air extraction system.	AS00.00-Z-0007-01A
 Caution	Risk of injury caused by scraping or cutting body parts on sharp vehicle parts	Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. Deburr repair panels.	AS00.00-Z-0017-01A
Topical note	General information on vehicles with high-voltage on-board electrical system and/or lithium-ion battery and/or gaseous-fuel drive system as well as personal protective equipment	Model 447 with engine 780	AH00.00-Z-0300-01A
Topical note	Pretreatment of bonding surfaces		AH60.00-P-0008-01SX
Topical note	Measures for preventing damage to vehicles or components when performing electric welding work		AH00.00-N-0005-01A
Topical note	General information on body repair		AH60.00-N-0001-01A
Topical note	Notes on battery		AH54.10-P-0001-01A
	General information on riveting		AH60.00-P-0003-01N
	General information on MB materials		AH98.00-P-9409-03A
	Remove
1	Remove all detachable parts in area of repair point.
2	Remove soundproofing.		AR60.00-S-1752E
		 Only in repair area.
3	Cover all detachable parts remaining in vehicle with welding protection blankets.	 Commercially available devices/tools Welding protection blanket
4	Set up straightening bench with crossbars and straightening tool set.
	000 588 01 23 00 Body straightening system		WS60.00-P-0023K
5	Remove upper front longitudinal member.		AR62.20-S-1286-01E
	000 588 00 84 00 Heat gun		WS54.00-P-0049B
		 Commercially available devices/tools Spot weld milling machine Rotary wire brush Wet and dry vacuum cleaner
		Zinc dust paint suitable for spot welding	*BR00.45-Z-1001-07A
6	Place vehicle on straightening bench and fasten.
	000 588 01 80 00 Swivel arm vehicle lift		WS00.00-P-0041B
7	Remove A-pillar outer section (1).		AR63.20-S-1102-01E
	000 588 00 84 00 Heat gun		WS54.00-P-0049B
		 Commercially available devices/tools Body power jigsaw Rotary wire brush Spindle grinder Spot weld milling machine
8	Prepare A-pillar outer section (1) and door hinge brackets (4) for installation.		AR63.20-S-1102-02E
	000 588 01 84 00 Welder		WS60.00-P-0021K
		 Commercially available devices/tools Body power jigsaw Hole punching pliers Hand drill Rotary wire brush Wet and dry vacuum cleaner
		Zinc dust paint suitable for spot welding	*BR00.45-Z-1001-07A
9	Prepare upper front longitudinal member.		AR62.20-S-1286-02E
		 Commercially available devices/tools Rotary wire brush Wet and dry vacuum cleaner
		Zinc dust paint suitable for spot welding	*BR00.45-Z-1001-07A
10	Install dowels for brackets on longitudinal member panel.	Model 447.8, 448.8	AR88.80-S-6005-01CH
Topical note	Notes on removing adhesive residues and foils on paint and metal surfaces with surface conditioning disks		AH00.00-P-0013-01AK
		 Commercially available devices/tools Surface conditioning disk Ø 100 mm
		Primer Teroson 150 (Terokal 150)	*BR00.45-Z-1179-02A
		Teroson PU 6800 adhesive	*BR00.45-Z-1147-02A
		Cleaner	*BR00.45-Z-1025-04A
		Primer stick	*BR00.45-Z-1012-07A
	Install
11	Install A-pillar outer section (1) and door hinge brackets (4).		AR63.20-S-1102-03E
	000 588 01 84 00 Welder		WS60.00-P-0021K
	000 588 02 84 00 Welder		WS60.00-P-0022K
	000 588 01 23 00 Body straightening system		WS60.00-P-0023K
		 Commercially available devices/tools Clamping pliers (Standard) Rotary wire brush Angular grinder Wet and dry vacuum cleaner
		Gap dimensions	*BE60.00-N-1004-01J
		White sealing compound, 310 ml, DBL 6069.20	*BR00.45-Z-1003-01A
		 Feeler gauge	*129589032100
		 Side portal frame	*210589172300
12	Install corresponding welding fixture.	Model 447 with engine 622, 780	AR62.20-S-1286-05EFA
Topical note	Notes on threaded connections fastened using a tightening angle-based tightening process		AH00.00-P-0020-01A
		Model 447 with engine 274, 651, 654 Model 448 with engine 274	AR62.20-S-1286-05EFE
		 Bolt, suspension strut to body	*BA32.25-N-1004-04C
		 Model 447 with engine 274, 651, 654 Model 448 with engine 274 Welding device	*447589022300
		 Model 447 with engine 622, 780 Welding device	*447589032300
13	Install and weld in upper front longitudinal member with welding fixture.		AR62.20-S-1286-03E
	000 588 01 84 00 Welder		WS60.00-P-0021K
		 Commercially available devices/tools Clamping pliers (Standard) Hand drill Blind riveting tool (setting force > 19 kN) Rotary wire brush Wet and dry vacuum cleaner
		Blind rivet 6.414 (clamping range 1 mm to 8.5 mm, draw-off strength min. 10.8 kN)	*BR00.45-Z-1001-13A
		Zinc dust paint suitable for spot welding	*BR00.45-Z-1001-07A
		Adhesive kit, body, 2-component adhesive	*BR00.45-Z-1092-02A
		 Model 447 with engine 274, 651, 654 Model 448 with engine 274 Welding device	*447589022300
		 Model 447 with engine 622, 780 Welding device	*447589032300
14	Remove corresponding welding fixture.	 Model 447 with engine 274, 651, 654 Model 448 with engine 274 Welding device	*447589022300
		 Model 447 with engine 622, 780 Welding device	*447589032300
15	Clean weld joints and sheet metal flanges with rotary wire brush.	 Commercially available devices/tools Rotary wire brush
16	Release vehicle from straightening bench, lift and remove straightening bench.
17	Remove welding protection blankets.	 Commercially available devices/tools Welding protection blanket
18	Clean repair area.	 Commercially available devices/tools Wet and dry vacuum cleaner
 Danger	Risk of explosion caused by paint vapors igniting. Risk of poisoning caused by inhaling paint vapors.	No smoking! No open fire! Use respiratory protection, protective clothing, gloves, safety glasses and protective skin cream. Ensure that the area is well ventilated.	AS98.00-Z-0002-01A
19	Prime repair area with a primer filler.
Topical note	Notes on paintwork repairs		AH98.00-P-9408-02A
		 Use only primer filler approved by Daimler AG: http://xentryportal.mercedes-benz.com
20	Seal seam after repair.		AR97.10-S-4000E
		 Supplement standard seals with sealant.
 Danger	Risk of explosion caused by paint vapors igniting. Risk of poisoning caused by inhaling paint vapors.	No smoking! No open fire! Use respiratory protection, protective clothing, gloves, safety glasses and protective skin cream. Ensure that the area is well ventilated.	AS98.00-Z-0002-01A
21	Paint repair area and adjacent surfaces.
Topical note	Notes on paintwork repairs		AH98.00-P-9408-02A
		 Use only paints approved by Daimler AG: http://xentryportal.mercedes-benz.com
22	Supplement cavity preservation.		AR97.20-S-1500E
23	Install soundproofing.		AR60.00-S-1752E
		 Only in repair area.
24	Install all detachable parts in area of repair point.

Gap dimensions

Number	Designation				Model 447, 448 except code W64, W65, W68	Model 447, 448 with code W64, W65, W68
BE60.00-N-1004-01J	Gap dimensions	Front door to longitudinal member	Dimension "DA"	mm	6 (+2/-1)	6 (+2/-1)
		Front door to sidewall	Dimension "DB"	mm	4 (1)	4 (1)
		Front door to sliding door	Dimension "DC"	mm	4 (+1,2/-0,8)	4 (+1,2/-0,8)
		Front door to A-pillar	Dimension "DD"	mm	4,5 (+1,5/-1)	4,5 (+1,5/-1)
		Front door to fuel filler door	Dimension "DE"	mm	4 (1)	4 (1)
			For picture, see		AR60.00-S-0700-01E	AR60.00-S-0700-01E

 Suspension struts

Number	Designation			Model 447, 448
BA32.25-N-1004-04C	Bolt, suspension strut to body	Stage 1	Nm	40
		Stage 2	°	90

210 589 17 23 00

Side portal frame

447 589 02 23 00

Welding device

129 589 03 21 00

Feeler gauge

447 589 03 23 00

Welding device

Repair materials

Number	Designation	Order number
BR00.45-Z-1001-07A	Zinc dust paint suitable for spot welding	A 000 986 34 42
BR00.45-Z-1001-13A	Blind rivet 6.414 (clamping range 1 mm to 8.5 mm, draw-off strength min. 10.8 kN)	A 003 990 35 97
BR00.45-Z-1003-01A	White sealing compound, 310 ml, DBL 6069.20	A 001 989 63 20
BR00.45-Z-1012-07A	Primer stick	A 000 986 27 50
BR00.45-Z-1025-04A	Cleaner	A 005 989 19 71
BR00.45-Z-1092-02A	Adhesive kit, body, 2-component adhesive	A 012 989 17 71
BR00.45-Z-1147-02A	Teroson PU 6800 adhesive	A 000 989 15 02 09
BR00.45-Z-1179-02A	Primer Teroson 150 (Terokal 150)	Henkel AG & Co. KGaA http://www.loctite.de

Referenced documents

ah0000n000501a Measures for preventing damage to vehicles or components when performing electric welding work
ah0000p001301ak Notes on removing adhesive residues and foils on paint and metal surfaces with surface conditioning disks
ah0000p002001a Notes on threaded connections fastened using a tightening angle-based tightening process
ah0000z030001a General information on vehicles with high-voltage on-board electrical system and/or lithium-ion battery and/or gaseous-fuel drive system as well as personal protective equipment
ah5410p000101a Notes on battery
ah5410p000101a
ah6000n000101a General information on body repair
ah6000p000301n General information on riveting
ah6000p000801sx Pretreatment of bonding surfaces
ah9800p940802a Notes on paintwork repairs
ah9800p940903a General information on MB materials
ar6000s1752e Remove, install soundproofing
ar6220s128601e Separate upper front longitudinal member
ar6220s128602e Prepare upper front longitudinal member
ar6220s128603e Install upper front longitudinal member
ar6220s128605efa Install welding device
ar6220s128605efe Install welding device
ar6320s110201e Separate A-pillar outer section
ar6320s110202e Prepare A-pillar outer section for installation
ar6320s110203e Install A-pillar outer section
ar8880s600501ch
ar8880s600501ch Remove/install dowel for mounting rail of longitudinal member panel
ar9710s4000e Seam sealing following repair
ar9720s1500e Cavity preservation following repair work
as0000z000701a The high voltage used for electric welding presents a lethal hazard. Risk of explosion from welding in areas close to highly inflammable materials. Risk of injury from weld splatter and UV-light when welding. Risk of poisoning from
as0000z001001a Risk of death caused by vehicle slipping or toppling off of the lifting platform.
as0000z001701a Risk of injury caused by scraping or cutting body parts on sharp vehicle parts
as0000z003501a Risk of death when working on component parts and systems with U >= 30 V alternating voltage (AC) or U >= 60 V direct voltage (DC)
as9800z000201a Risk of explosion caused by paint vapors igniting. Risk of poisoning caused by inhaling paint vapors.
ws0000p0041b 000 588 01 80 00 Swivel arm vehicle lift
ws5400p0049b 000 588 00 84 00 Heat gun
ws6000p0021k 000 588 01 84 00 Welder
ws6000p0022k 000 588 02 84 00 Welder
ws6000p0023k 000 588 01 23 00 Body straightening system