ar6000s0019e

Remove/install exterior detachable parts and trim in vehicle interior for replacing sidewall up to sliding door guide rail

Type ar · topic 60.00 · version 0500 · 2020-05-20

Applies to: Model 447, 448 with code T19 (Sliding door left) Left side of vehicle

Where it sits

Function group 3 Body › 60 Body - general › 60.00 General — Series 447 · Series 448

EinPAS 35 Body/frame/detachable parts › 35.34 Sidewall › 35.34.35 Fender/sidewall — Series 447 · Series 448

AR60.00-S-0019E

Remove/install exterior detachable parts and trim in vehicle interior for replacing sidewall up to sliding door guide rail

04.05.2020

Model

447, 448

with code T19 (Sliding door left)

Left side of vehicle

Modification notes

18.12.2019

Method extended

Operation step 16

30.04.2020

Method extended

Operation steps 20, 21

Remove/install exterior detachable parts and trim in vehicle interior for replacing sidewall up to sliding door guide rail

Shown on model 447.8 with code EL9 (2-way speaker system, front and rear) and with code HZ7 (Semiautomatically controlled air conditioning system, TEMPMATIC in rear) and with code T56 (Electrical actuation for left sliding door)

1

Air duct

2

Mounting clip

3

Bolts

4

Bracket

5

Nuts

6

Bracket

7

Bolts

8

Air duct

9

Air duct

H4/3

Left rear side wall speaker

S60.00-4602-06

Remove/install exterior detachable parts and trim in vehicle interior for replacing sidewall up to sliding door guide rail

S60.00-4603-09

Shown on model 447.8 with code T56 (Electrical actuation for left sliding door)

10

Lock striker

12

Nut

14

Rear section

11

End stop

13

Mounting clip

15

Axle mount cover

Danger

Risk of death when working on component parts and systems with U >= 30 V alternating voltage (AC) or U >= 60 V direct voltage (DC)

Do not touch damaged or defective live component parts and lines or non-insulated electrical connections and lines.Typ 447 mit Motor 780

AS00.00-Z-0035-01A

Danger

Risk of death caused by vehicle slipping or toppling off of the lifting platform.

Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer.

AS00.00-Z-0010-01A

Topical note

General information on vehicles with high-voltage on-board electrical system and/or lithium-ion battery and/or gaseous-fuel drive system as well as personal protective equipment

Typ 447 mit Motor 780

AH00.00-Z-0300-01A

Topical note

Notes on carrying out repair work in the vehicle interior

AH68.00-N-0001-01S

Remove/install

1

Detach ground line of on-board electrical system battery.

AR54.10-S-0003E

2

Disconnect ground line of auxiliary battery.


Model 447.6/7 with code E28 (Additional battery for retrofit consumer), model 447.7/8 with code EE9 (Auxiliary battery 12 V/80 Ah), model 447.8 with code EE8 (Battery 12V 100 Ah)

AR54.10-S-0004E

3

Remove ground line of the auxiliary battery for ECO start/stop function.


Model 447 with code MJ8 (ECO start/stop function) except code D50 (Full-width partition wall) except code D51 (Full-width partition wall with 1 window) except code S23 (Two-seater front passenger seat), model 448

AR54.10-S-0111E

Model 447 with code D50 (Full-width partition wall) with code MJ8 (ECO start/stop function), Model 447 with code D51 (Full-width partition wall with 1 window) with code MJ8 (ECO start/stop function), Model 447 with code MJ8 (ECO start/stop function) with code S23 (Two-seater front passenger seat)

AR54.10-S-0111EE

4

Disconnect ground on additional battery for park pawl emergency shift.


Model 447 with engine 780 except code G42 (7G-TRONIC PLUS) except code G43 (9G-TRONIC), model 447 with code G42 (7G-TRONIC PLUS) except code MJ8 (ECO start/stop function), model 447 with code G43 (9G-TRONIC) except code MJ8 (ECO start/stop function)

AR54.10-S-0120E

5

Remove fender liner in rear fender.

If installed.

AR88.10-S-1400E

6

Remove rear bumper.

AR88.20-S-2200E

7

Remove side part holder for rear bumper.

AR88.20-S-9018E

8

Remove sliding door.

AR72.16-S-1260E

If sliding door will be replaced,

Disassemble sliding door.


AR72.16-S-2210E

9

Remove mounting rail on longitudinal member panel in repair area.


Model 447.8, 448.8

AR88.80-S-6005CH

10

Remove center guide rail for sliding door.

AR72.16-S-7806E

11

Remove sealing frame on sliding door.

AR72.16-S-2120E

12

Remove door sill from sliding door.

AR68.30-S-1312E

13

Remove lock striker (10).

Screw/bolt, lock striker to C-pillar

*BA72.16-N-1005-01J

14

Remove end stop (11).

15

Remove underbody paneling.


Model 447 with engine 651 with code MX0 (BlueEFFICIENCY package), Model 447 with engine 654.9

AR61.30-S-1001E

16

Remove high-voltage battery module underfloor paneling.

* Applies to Europe only

Model 447 with engine 780.701

AR61.30-S-1001F

17

Remove nut (12) on rear section (14) of underfloor paneling.

Model 447 with engine 651 with code MX0 (BlueEFFICIENCY package), Model 447 with engine 654.9

18

Remove rear section (14) of underfloor paneling.

Model 447 with engine 651 with code MX0 (BlueEFFICIENCY package), Model 447 with engine 654.9

To do so, remove retaining clip (13).

19

Remove axle mount trim (15).

20

Remove coolant lines of rear heater at underbody in working area.


Model 447.7/8 with code H13 (Rear additional heat exchanger), model 447.7/8 with code HZ7 (Semiautomatically controlled air conditioning system, TEMPMATIC in rear), model 448

AR83.60-S-0013E

Do not drain coolant, do not remove coolant hoses.

21

Remove refrigerant lines of rear air conditioning system at underbody on left in working area.

Model 447.7 with engine 622 with code HZ7 (Semiautomatically controlled air conditioning system, TEMPMATIC in rear), model 447.7/8 with engine 274, 651, 654 with code HZ7 (Semiautomatically controlled air conditioning system, TEMPMATIC in rear), model 448

For this purpose, open respective brackets.
Do not extract refrigerant and do not disconnect refrigerant lines.

22

Disconnect electrical connectors on left rear side wall speaker (H4/3).

Model 447.7/8, 448 with code EL9 (Front and rear two-way speaker system) Model 447.8, 448.8 with code E65 (Burmester surround sound system)

23

Remove left rear side wall speaker (H4/3) with bracket (6).

Model 447.7/8, 448 with code EL9 (Front and rear two-way speaker system) Model 447.8, 448.8 with code E65 (Burmester surround sound system)

To do this, remove bolts (7).

24

Remove air duct (1).

Model 447.7/8 with code H13 (Rear additional heat exchanger), model 447.7/8 with code HZ7 (Semiautomatically controlled air conditioning system, TEMPMATIC in rear), model 448

To do so, remove retaining clip (2).

25

Remove bracket (4).

To do this, remove screws/bolts (3).

26

Remove electric sliding door drive unit.


Model 447.7/8, 448.8 with code T56 (Electrical actuation for left sliding door)

AR72.29-S-8788E

27

Remove rear air recirculation unit.


Model 447.7/8 with code H13 (Rear additional heat exchanger), model 447.7/8 with code HZ7 (Semiautomatically controlled air conditioning system, TEMPMATIC in rear), model 448

AR83.60-S-7175E

28

Remove air duct (8).

Model 447.7/8 with code H13 (Rear additional heat exchanger), model 447.7/8 with code HZ7 (Semiautomatically controlled air conditioning system, TEMPMATIC in rear), model 448

29

Remove air duct (9).

Model 447.7/8 with code H13 (Rear additional heat exchanger), model 447.7/8 with code HZ7 (Semiautomatically controlled air conditioning system, TEMPMATIC in rear), model 448

To do so, remove nuts (5).

30

Install in the reverse order.

Sliding doors

Number

Designation

Model 447, 448

BA72.16-N-1005-01J

Screw/bolt, lock striker to C-pillar

Nm

20

Referenced documents