W26.10-0030-09
1 Heat shield
2 Clip
3 Exhaust pipe
4 Compressed-air line
5 Gearshift lever
6 Neutral position switch connector
13 Transmission bearing bracket
14 Speedometer sensor connection
15 Clutch slave cylinder
(up to veh. no.: 099977)
Central clutch operator hose
(as of veh. no.: 099978)
16 Exhaust pipe bracket
17 Bolts
18 Backup lamp switch connector
7 Propeller shaft
8 Nut
9 Crossmember
10 Rubber bushing
11 Console cover
12 Mounting console
| Remove/install | ||
1 | Remove maintenance cover | ||
2 | Detach heat shield (1) from top of exhaust manifold | ||
3 | Release clamp (2) from exhaust pipe (3) | ||
4 | Remove shift lever (5) | ||
5 | Remove soundproofing | ||
6 | Detach exhaust pipe bracket (16) from transmission and push exhaust pipe (3) to the side | ||
7 | Detach compressed-air line (4) from compressor to compressed-air drier from transmission and separate | On vehicles with CODE B16 | |
8 | Remove propeller shaft | ||
9 | Detach propeller shaft from transmission and propeller shaft intermediate bearing | On vehicles with split propeller shaft | |
10.1 | Disconnect propeller shaft (7) from PTO | On vehicles with PTO | |
| |||
10.2 | Detach power take-off connections | ||
11 | Release and detach speedometer sensor connection (14) | Attach new tamperproof seal on speedometer sensor connection | |
12 | Unplug connector from neutral position switch (6) | ||
13 | Unplug connector from backup lamp switch (18) | ||
14 | Detach clutch slave cylinder (15) Detach central clutch operator hose | ||
| |||
15 | Remove console cover (11) | | |
16 | Support engine | ||
17 | Support transmission | Pit lift 2.0-7.0 t | |
Position wooden wedges between body and frame side member | |||
18 | Unfasten crossmember (9) from left and right frame side members and push towards the rear | Installation: Use new nuts (8) | |
19 | Remove console (12) | ||
| |||
20 | Detach transmission bearing bracket (13) from transmission | | |
21 | Unscrew bolts (17) and lift out transmission | Lower transmission with engine a little, pull out transmission towards the rear and lower | |
Installation: Coat splined profile of input shaft with long-term grease. | |||
| |||
22 | Install in the reverse order | ||
23 | Bleed hydraulic PTO actuation system | On vehicles with PTO | |
24 | Inspect transmission oil level | ||
25 | Check transmission for function and leaks |
Clutch operating mechanism
Number | Designation | Engine | ||
BA25.20-N-1002-01E | Clutch slave cylinder on transmission | Nm | 25 | |
Manual transmission complete
Number | Designation | Trans-mission 710.640 | |
BA26.10-N-1001-01B | Transmission bearing bracket on transmission | Nm | 96 |
BA26.10-N-1003-01B | Transmission to engine | Nm | 50 |
BA26.10-N-1004-01B | Bolt, console to transmission bearing bracket | Nm | 50 |
BA26.10-N-1005-01B | Bolt, console cover to console | Nm | 50 |
Propeller shaft of PTO
Number | Designation | NA ZF-2b transmission 710.6 | |
BA41.20-N-1001-01C | Propeller shaft to PTO | Nm | 23 |
Repair materials
Number | Designation | Order number |
BR00.45-Z-1008-02A | Quick-acting adhesive, Loctite 270 | A 002 989 93 71 |
Referenced documents
- ap2600d2601a Manual transmission - oil change
- ar2520d015001d Detach, attach slave cylinder at transmission
- ar2610d002001d Detach, attach transmission bearing bracket at transmission
- ar2619d000101d Separate, connect plug connection at reversing light switch
- ar2619d000103d Separate, connect plug connection at neutral position switch
- ar2619d000104d Detach, attach speedometer sensor connection at transmission
- ar2660d6600b Removing and installing shift lever
- ar4110d0050a Remove/install propeller shaft