AR83.70-W-5930J | Remove/install control unit from heater | 28.6.06 |
MODEL 375.1 with BODY 375.830 with CODE (H13) "Eberspächer" D2 S warm air auxiliary heater
MODEL 375.3 with BODY 375.810 with CODE (H13) "Eberspächer" D2 S warm air auxiliary heater
MODEL 375.4 with BODY 375.840 with CODE (H13) "Eberspächer" D2 S warm air auxiliary heater
MODEL 944 with BODY 944.899 with CODE (H13) "Eberspächer" D2 S warm air auxiliary heater
MODEL 950, 952, 953, 954 with BODY 940.899 with CODE (H13) "Eberspächer" D2 S warm air auxiliary heater
MODEL 970, 972, 974, 975, 976 with BODY 972.899 with CODE (H13) "Eberspächer" D2 S warm air auxiliary heater
MODEL 375.1 with BODY 375.850 with CODE (HZ3) Warm air auxiliary heater, 2000W
MODEL 375.3 with BODY 375.820 with CODE (HZ3) Warm air auxiliary heater, 2000W
MODEL 375.4 with BODY 375.860 with CODE (HZ3) Warm air auxiliary heater, 2000W
MODEL 940, 942, 943, 944 with BODY 944.890 with CODE (HZ3) Warm air auxiliary heater, 2000W
MODEL 950, 952, 953, 954 with BODY 940.890 with CODE (HZ3) Warm air auxiliary heater, 2000W
MODEL 970, 972, 974, 975, 976 with BODY 972.890 with CODE (HZ3) Warm air auxiliary heater, 2000W
MODEL NAB374.602 /651 /655 /682 /685 with BODY 374.870 with CODE (HZ3) Warm air auxiliary heater, 2000W
W83.70-1297-11
2 Cable grommet
3 Lower housing segment
4 Control unit
5 Bolt
6 Retaining clamp
7 Heater unit electrical line
W83.70-1298-11
4 Control unit
8 Electrical connectors
| Remove/install | ||
Danger! | Risk of explosion caused by fuel vapors igniting, risk of poisoning caused by inhaling combustible gases and risk of injury caused by burns during and after operation of heater unit | Do not operate stationary heater, auxiliary heater or engine with heater booster in closed areas or when refueling. Allow heater unit to cool down after operation and wear protective gloves. | |
1 | Detach electrical connector from heater unit | When in the heating mode or during the run-on phase, the heater unit's power supply must not be interrupted. | |
2 | Remove upper housing shell | ||
3 | Detach heater unit electrical line (7) with cable grommet (2) from lower housing shell (3) | ||
4 | Remove control unit (4) | Remove bolt (5). Push retaining clamp (6) together and remove control unit (4) upwards until the electrical connectors (8) on the control unit (4) are accessible. | |
| |||
5 | Detach electrical connectors (8) on the control unit (4) | The electrical connectors (8) are coded and cannot be interchanged. | |
6 | Install in the reverse order | ||
7 | Check function of heater | See heater unit operating instructions. |
Stationary heater unit
Number | Designation | Model | Model | Model | ||
BA83.70-N-1004-03F | Screw, auxiliary heater control unit to | Nm | 2 | 2 | 2 | |
Stationary heater unit
Number | Designation | Model | Model | Model | ||
BA83.70-N-1004-03F | Screw, auxiliary heater control unit to | Nm | 2 | 2 | 2 | |
Stationary heater unit
Number | Designation | Model | Model | Model | ||
BA83.70-N-1004-03F | Screw, auxiliary heater control unit to | Nm | 2 | 2 | 2 | |
Stationary heater unit
Number | Designation | Model | Model | Model | ||
BA83.70-N-1004-03F | Screw, auxiliary heater control unit to | Nm | 2 | 2 | 2 | |
Stationary heater unit
Henviste dokumenter
- ar8370w5808j
- as8370z000201a Fare for eksplosion på grund af brændstofdampe, fare for forgiftning ved indånding af forbrændingsgas og fare for personskade på grund af forbrændinger, under eller efter at varmesystemet har været i drift.