W72.10-1076-09
Shown on driver door
1 Screw
2 Protective tubing
3 Footwell cover
4 Door module
5 Cover
X22.1 Driver door plug connection
X23.1 Passenger door plug connection
X24 Driver door mirror connector
X25 Front passenger door mirror connector
6 Bolts
8 Retaining rail
E25 Driver door entrance lamp
E26 Front passenger door entrance lamp
W72.10-1023-11
7 Screw
Modification notes
5.12.11 | Work procedure completely revised. | ||
Injury hazard caused by scraping or cutting body parts on sharp vehicle parts added. | |||
5.1.12 | Work procedure revised completely according to worker's council study dated 14.12.2011. |
| Remove/install | ||
| Notes on self-locking nuts and bolts | ||
1 | Switch off ignition | ||
2 | Remove cover (5) | Assembly wedge | |
3 | Remove outside door handle | ||
4 | Manually close door lock | Facilitates removal and installation of door module (4). | |
5 | Unscrew bolts (6) from door lock | The door lock is fastened to the door module (4) and can only be removed in combination with the door module (4). | |
| |||
6 | Remove speaker in front door | Only if power window motor is defective. | |
Danger! | Risk of injury due to hands being crushed when window glass is not secure | Secure window to prevent it from falling down. | |
Danger! | Risk of injury caused by scraping or cutting body parts on sharp vehicle parts | Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. Deburr repair panels. | |
7 | Remove power window motor from door module (4) | Only if power window motor is defective. | |
Ensure that the retaining strip (8) of the lowered window does not hit against the door frame. Otherwise the door frame can be damaged. | |||
8 | Remove footwell cover (3) | Driver side | |
Passenger side | |||
9 | Disconnect drive door connector (X22.1) or passenger door connector (X23.1) | ||
10 | Remove protective hose (2) from A-pillar and door | ||
11 | Guide electrical wiring harness on driver or passenger door through opening in | ||
12 | Connect driver door connector (X22.1) and passenger door connector (X23.1) | Only if power window motor operates properly. | |
13 | Switch on ignition | Only if power window motor operates properly. | |
14 | Unscrew bolt (7) | If necessary, lift window until bolts (7) are accessible. | |
15 | Remove driver door entrance lamp (E25) or passenger door entrance lamp (E26) | Do not disconnect electrical connector. | |
16 | Unscrew all bolts (1) from door module (4) | ||
17 | Remove door module (4) | Loosen power window from widow guides in door frame, lift door module (4) at rear, push toward front and then remove upward. | |
Ensure that the retaining strip (8) of power window does not chafe on the door frame.Otherwise the door frame can be damaged. | |||
18 | Switch off ignition | ||
19 | Disconnect drive door connector (X22.1) or passenger door connector (X23.1) | Only if power window motor operates properly. | |
20 | Guide electrical wiring harness on driver or passenger door through opening in door | ||
21 | Disconnect electrical connector from driver door entrance lamp (E25) and passenger door entrance lamp (E26) | ||
22 | Disconnect driver door mirror connector (X24) or passenger door mirror connector (X25) | ||
23 | Install in the reverse order | ||
24 | Check power window for anti-pinch protection | Only on vehicles with code (FZ3) Comfort locking system with remote control. |
Front door
Number | Designation | Model | |
BA72.10-N-1002-01B | Bolt, door lock/lock switch on door | Nm | 7 |
Mounting wedge
110 589 03 59 00
Henviste dokumenter
- ah0000n000101a Oplysninger om selvlåsende bolte og møtrikker
- ar6830w1300mp
- ar6830w1310c
- ar7210w090001a
- ar7210w2400d
- ar7229w2200h
- ar8262w7845a Af-, påmongering af højttalere i fordørene
- as0000z001701a Fare for personskade på grund af snitsår eller hudafskrabninger grundet skarpkantede køretøjsdele
- as6700z000201a Fare for knusning af hænderne, hvis ruden ikke er sikret