ar7220p3500mce

Remove/install rear-end door

Typ ar · téma 72.20 · verze 0102 · 2007-10-17

Platí pro: MODEL 451.3

Není k dispozici v jazyce „cs“; zobrazeno v jazyce Angličtina.

Zařazení

Funkční skupina 3 Nástavba › 72 Dveře › 72.20 Dveře zadní stěny, zadní čelní dveře — Řada 451 (modely 3**)

EinPAS 35 Karoserie/rám/montované díly › 35.35 Dveře › 35.35.43 Zadní dveře — Řada 451 (modely 3**)

AR72.20-P-3500MCE

Remove/install rear-end door

4.10.07

MODEL 451.3

Remove/install rear-end door

P72.20-2660-09

1 Rear-end door wiring harness

2 Side trunk lining

3 Pulling aid

7 Gas-operated strut

8 Rear-end door

9 Grommet

4 Door hinge

5 Screw

6 Retainer

Remove/install

1

Remove cover on left side luggage compartment paneling (2).

2

Guide rear-end door wiring harness (1) out of body opening

3

Push back foam rubber jacketing (arrow) and disconnect all electrical connectors as well as water fluid hose on rear-end door wiring harness (1).

4

Loosen grommet (9) on rear-end door wiring harness (1) in area of left door hinge (4).

Installation: Arrow on grommet (9) should coincide with marking on body.

5

Fasten suitable pulling out (3) on rear-end door wiring harness (1) and guide rear-end door (1) upward out of vehicle.

Danger!

Risk of injury Gas pressure struts are under high pressure and can pinch and crush body parts during work

Remove and install gas pressure struts only in relaxed position and on components properly secured.

AS00.00-Z-0012-01A

6

Lift retainers (6) with suitable screwdriver and unclip gas-operated strut (7) on rear-end door (8).

Ensure that rear-end door (8) does not close unintentionally to prevent damage.

Do not remove retainers (6) because otherwise tension on retainers (6) is lost.

Installation: Clip gas-operated strut (7) to ball heads on rear-end door (8) using retainers (6) clipped in.

7

Remove bolts (5) from door hinges (4) and take off rear-end door (8).

Aid of helper required.

Installation: Check gaps on rear-end door (8), adjust if necessary.$ Refer to:

Adjust rear-end door (8)

AR72.20-P-3510MCD

*BA72.20-P-1006-02F

8

Remove rear-end door wiper motor

When replacing rear-end door (8).

AR82.30-P-6900MCC

9

Remove center high-mounted brake lamp

When replacing rear-end door (8).

AR82.10-P-5375MCC

10

Remove rear spoiler

When replacing rear-end door (8).

AR88.30-P-0500MCC

11

Remove ball heads from gas-operated struts (7).

When replacing rear-end door (8).

*BA72.20-P-1008-02F

12

Expose rear-end door wiring harness (1) on rear-end door (8) and remove.

When replacing rear-end door (8).

13

Install in the reverse order

14

Check rear window heater, rear wiper system and center high-mounted brake lamp for proper function

Rear-end door

Number

Designation

Model
451.3

BA72.20-P-1006-02F

Bolt, hinge to glass pane

Nm

12

BA72.20-P-1008-02F

Gas-operated spring ball head to upper rear-end door

Nm

12

Odkazované dokumenty