ar2210p1260a

Remove/install front engine mounts and/or engine support

Typ ar · téma 22.10 · verze 0116 · 2009-11-17

Platí pro: ENGINES 112, 113 / (except 112.975, 113.948 /966) in MODEL 220

Není k dispozici v jazyce „cs“; zobrazeno v jazyce Angličtina.

Zařazení

Funkční skupina 1 Motor › 22 Zavěšení agregátů › 22.10 Uložení agregátů, nosič agregátů — Řada 220

EinPAS 15 Motor › 15.15 Kompletní spalovací motor/blok motoru/klikový mechanismus › 15.15.20 Zavěšení motoru — Řada 220

Platí také pro motory/převodovky: 112 910, 112 911, 112 912, 112 913, 112 914, 112 915, 112 916, 112 917, 112 920, 112 921, 112 922, 112 923, 112 925, 112 940, 112 941, 112 942, 112 943, 112 944, 112 945, 112 946, 112 947, 112 949, 112 951, 112 953, 112 954, 112 955, 112 960, 112 961, 112 970, 112 972, 112 973, 112 976, 113 940, 113 941, 113 942, 113 943, 113 944, 113 960, 113 961, 113 962, 113 963, 113 964, 113 965, 113 967, 113 968, 113 969, 113 971, 113 980, 113 981, 113 982, 113 984, 113 985, 113 986, 113 987, 113 988, 113 989, 113 990, 113 991, 113 992, 113 993, 113 994, 113 995

AR22.10-P-1260A

Remove/install front engine mounts and/or engine support

3.11.09

ENGINES 112, 113 / (except 112.975, 113.948 /966) in MODEL 220

Remove/install front engine mounts and/or engine support

P22.10-2022-06

1 Air filter housing with intake pipes

2 Poly-V-belt

5 Bolts, engine mount to front-axle carrier

6 Bolt for left engine mount

7 Bolt for right engine mount

8 Left engine mount

9 Right engine mount

10 Left engine support

11 Right engine support

12 Bolts on engine supports

13 Power steering pump

A9 Refrigerant compressor

G2 Alternator

Remove/install

Notes on Active Body Control suspension

AH32.50-P-0001-01N

Right engine side (removal of engine mount and engine support)

1

Disconnect/connect battery ground line

Turn key in electronic ignition lock EIS into position "0". Key cannot be withdrawn.

AR54.10-P-0003I

Notes on battery

AH54.10-P-0001-01A

Vehicles with Keyless Go code 889:

Switch engine off, remove Keyless-Go cards from the vehicle and store outside of the transmitter range.

Do not connect quiescent current retention unit. A short circuit could occur, if the electrical line circuit 30 (B+) comes into contact with the ground.

2

Remove lower engine compartment paneling

AR61.20-P-1105M

3

Unclip cover on front end of engine.

4

Remove air filter housing with air intake pipes (1)

5

Remove poly-V belt

Except engine 113.991

AR13.22-P-1202BA

Engine 113.991

AR13.22-P-1202R

6

Disconnect electrical lines at generator (G2).

Installation: Note installation position of lines.

*BA15.40-P-1001-01A

7

Detach alternator (G2) and place in the engine compartment to the side

Engine 112.922/944, 113.941/960

*BA15.40-P-1003-01A

8

Put on engine carrier arm

AR01.10-P-7500-03I

9

Remove engine mount (5) bolts to front axle carrier

Remove on both sides.

The anti-twist locks in front axle beam must latch in retaining grooves of engine mount (8, 9).

*BA22.10-P-1001-01L

10

Raise engine at front lifting eye

Ensure that rear of engine does not touch the body.

11

Detach right engine support (11) at crankcase, for this step unscrew bolts (12) and take out right engine support (11) with engine mount (9) toward front.

Installation: Replace bolts (12).

*BA22.10-P-1001-02A

12

Detach engine mount (9) from right engine support (11)

Installation: The anti-twist lock () at the engine mount (9) must latch in the retaining groove in the engine support (11) (arrow).

*BA22.10-P-1004-01L

Dispose of engine mount at scrap yard.

Left engine side (removal of engine mount or engine mount with engine support)

13

Remove power steering pump (13)

Vehicles without Active Body Control Code 487a

AR46.30-P-0500B

Vehicles with Active Body Control Code 487a

AR46.30-P-0500NA

14

Detach refrigerant compressor (A9) from bracket and place to the side

Adjust Torx double end box wrench for lower front screw.

*BA83.55-P-1002-01A

Torx double end box wrench for removal of refrigerant compressor

WF58.50-P-8355-01A

15.1

Detach engine mount (8) from left engine support (10)

Removal of engine mount (8).

Installation: The anti-twist lock () at the engine mount (8) must latch in the retaining groove in the engine support (10) (arrow).

*BA22.10-P-1004-01L

Dispose of engine mount at scrap yard.

16.1

Detach left engine support (10) at crankcase, for this step unscrew bolts (12) and take out left engine support (10) with engine mount (8) toward front.

Removal of left engine support (10) and engine mount (8).

Installation: Replace bolts (12).

*BA22.10-P-1001-02A

17

Install in the reverse order

Engine mounts, engine supports

Number

Designation

Engine
112.922/944/972,
113.941/960,
137.970
in model 220

BA22.10-P-1001-01L

Bolt, front engine mount to front axle carrier

Nm

35

BA22.10-P-1004-01L

Bolt connecting front engine mount to engine support

Nm

55

Engine support (engine side)

Number

Designation

Engine 112 except 112.916/
953

Engine 112.916/
953

Engine
113

BA22.10-P-1001-02A

Bolt, engine support to cylinder crankcase

Stage 1

Nm

20

20

20

Stage 2

°

90

60

90

Refrigerant compressor

Number

Designation

Engine
112
in model 220

Engine
113
in model 203, 209, 211, 219, 220

BA83.55-P-1001-01A

Bolt, refrigerant compressor to bracket

Nm

20

20

BA83.55-P-1002-01A

Bolt, refrigerant lines to refrigerant compressor

Nm

20

20

Alternator

Number

Designation

Engine 112.91/92/94/
953/954/955/
96/97 except 112.976,
engine 113.94/96/98

BA15.40-P-1001-01A

Nut, circuit B+ to alternator

Nm

18

BA15.40-P-1003-01A

Alternator bolt

Nm

42

Odkazované dokumenty