ap4720t0730a

Fuel prefilter - clean filter element

Typ ap · téma 47.20 · verze 0101 · 2005-07-12

Platí pro: ENGINE 441 in MODEL 613.355 ENGINES 402, 446 in MODEL 613.455 /485 ENGINES 447, 489 in MODEL 671

Není k dispozici v jazyce „cs“; zobrazeno v jazyce Angličtina.

Zařazení

Funkční skupina 1 Motor › 47 Palivová soustava, přívod energie hnacího řetězce › 47.20 Palivové čerpadlo, filtr — Řada 441 · Řada 447 · Řada 613 (modely 355, 455, 485) · Řada 671

EinPAS 16 Zásobování motoru palivem/energií › 16.10 Zásobování palivem › 16.10.41 Filtr/odlučovač vody — Řada 441 · Řada 447 · Řada 613 (modely 355, 455, 485) · Řada 671

Platí také pro motory/převodovky: 402 ***, 446 ***, 489 ***

AP47.20-T-0730A

Fuel prefilter - clean filter element

4.11.98

ENGINE 441 in MODEL 613.355

ENGINES 402, 446 in MODEL 613.455 /485

ENGINES 447, 489 in MODEL 671

Fuel prefilter - clean filter element

T47.20-0005-06

Illustrated on model 613

Fuel prefilter without retaining clip

1 Filter bowl

2 Filter element

3 Sealing ring

4 Handle of hand priming pump

Fuel prefilter - clean filter element

T47.20-0006-02

Shown on model 671

Fuel prefilter with retaining clip

5 Inspection glass

6 Retaining clip

7 Knurled nut

Danger!

Risk of explosion if ignition takes place, risk of poisoning caused by inhaling fuel vapors or swallowing fuel as well as risk of injury to skin and eyes exposed to fuel.

No fire, sparks, naked flames or smoking.
Pour fuels only into suitable and appropriately marked containers.

Wear protective clothing when handling fuel.

AS47.00-Z-0001-01A

1

Clean the outside of the soiled fuel prefilter

2

Cover over cooling and heating water hoses positioned below the prefilter

3.1

Loosen knurled nut (7) of retaining clip and swivel retaining clip to the side. Remove and clean inspection glass (5) and filter element.

Fuel prefilter with retaining clip Blow out with compressed air. Replace a filter element which is soiled or damaged or inspection glass that is damaged at the sealing surface.

3.2

Unscrew filter bowl (1), take off filter element (2) and clean

Fuel prefilter without retaining clip Blow out with compressed air. Replace a filter element which is soiled or damaged or inspection glass that is damaged at the sealing surface.

4

Inspect seal (3), replace according to condition

Lightly grease or oil new seal (3).

5.1

Insert filter element (2) in filter bowl (1) and screw filter bowl onto filter housing

Fuel prefilter without retaining clip

5.2

Insert filter element in inspection glass (5)

5.3

Fit inspection glass on filter bowl, secure with retaining clip (6) and knurled nut (7).

Fuel prefilter with retaining clip

Filter element with push spring at bottom.

Ensure inspection glass is installed properly before tightening knurled nut.

6

Bleed fuel system

AP47.00-T-1720-01A

Danger!

Risk of accident as vehicle may start off by itself with the engine running. Risk of injury as working around the engine during start-up or while running may result in contusions and burns

Secure vehicle to prevent it from moving off by itself.
Wear closed and tight-fitting work clothes.
Do not grasp hot or rotating parts.

AS00.00-Z-0005-01A

7

Start engine

8

Inspect prefilter for leaks

Odkazované dokumenty