1 | Cover |
2 | AdBlue reservoir |
3 | Insulating hose |
4 | Insulating hose |
5 | Coolant tubes |
6 | AdBlue pipe |
7 | AdBlue pipe |
8 | Coolant tubes |
9 | Closing ring |
10 | Electrical connector |
17 | AdBlue temperature and level combined sensor (17B02) |
B14.40-0030-06
B14.40-0018-09
9 | Closing ring | 14 | Closing claw | 17 | AdBlue temperature and level combined sensor (17B02) | ||
11 | Claw type wrench | 15 | Claws holder | A | Final position "open" | ||
12 | Lever | 16 | O-ring | B | Final position "closed" | ||
13 | Opening |
| Remove/install | ||
Warning | Risk of burn injuries and scalding when working at AdBlue lines and the components attached to them. Risk of injury to skin and eyes when handling AdBlue. Risk of poisoning caused by swallowing AdBlue | Pour AdBlue into suitable containers only. Wait until the pressure is released before starting any work on the exhaust aftertreatment system. | |
1 | Turn off the battery master switch | ||
Notes on use, material properties and handling of AdBlue® | |||
2 | Open the AdBlue reservoir access cover | ||
Warning | Risk of injury to skin and eyes suffering scalding from contact with hot coolantspray. Risk of poisoning from swallowing coolant. | Do not open cooling system unless coolant temperature is below 90 °C. Open cap slowly and release the pressure. Do not pour coolant into beverage containers. | |
3 | Relieve the cooling system pressure | ||
Topical note | Notes on coolant | ||
4 | Remove the cover (1) | Replace the plastic cable clamp | |
5 | Open insulation hoses (3,4) in approx. 10 cm length and move backwards | Roller tongs | |
6 | Loosen the cooling pipe (5) and AdBlue pipe clamps (6) and detach pipe nozzles | Repeat this work step on the cooling pipe (8) and AdBlue pipe (7). | |
Clamp | |||
7 | Loosen the electrical connector (10) and remove the electrical line from the vehicle frame | Replace the plastic cable clamp | |
8 | Position the claw wrench (11) in the openings (13) of the closing ring (9) | Claw-type wrench | |
9 | Position the lever (12) in the claw wrench (11), and turn the closing ring (9) counterclockwise, until reaching the position "open" (A) | A high degree of strength is applied to this task. Closing ring engages and disengages on impact. Do not use any extension between the lever (12) and the claw wrench (9). | |
Turn the locking ring (9) clockwise until the locking tabs (15) lock into the closing claw cavities. | |||
10 | Remove the closing ring (9) | ||
11 | Remove the AdBlue SCR combined temperature and level sensor (17) | Using a clean and damp cloth, clean the O-ring contact surfaces (16). Replace the O-ring (16). Before mounting, slightly grease the O-Ring (16). | |
Use as sliding agent the prescribed MB silicon grease. The application of silicon grease must be extremely moderate, otherwise you may damage the exhaust gas aftertreatment system. | |||
ABS sensor grease | |||
12 | Install in reverse order | ||
13 | Check for tightness of AdBlue lines (6,7) and coolant lines (5,8) in the region of the pipe connections | Just visual inspection. |
000 589 54 37 00
Clamp
950 589 01 37 00
Roller tongs
001 589 00 07 00
Claw-type wrench
Atıfta bulunulan belgeler
- ah1440n000101a AdBlue uygulaması, madde özellikleri ve kullanımı ile ilgili hatırlatmalar
- ah2000n208001a Soğutma maddesine ilişkin açıklamalar
- as1440z000101a AdBlue hatlarında ve bu hatlara bağlı yapı parçaları ile çalışırken yanma ve haşlanma tehlikesi. AdBlue ile çalışırken deri ve gözlerde yaralanma tehlikesi. AdBlue'nin içilmesine bağlı zehirlenme tehlikesi
- as2000z000101a Dışarı atılan sıcak soğutma maddesinden dolayı deri ve gözlerde haşlanma nedeniyleYaralanma Tehlikesi. Soğutma maddesinin yutulmasından dolayı zehirlenmetehlikesi