Replacing steering shaft

SM46.10-W-0004C

Replacing steering shaft

21.07.2017

Model

930, 932, 933, 934, 950, 952, 953, 954 with steering gear 765.82/88

with code F15 (MEGASPACE cab)

Code: LENK-SP3

Operation no. of the operation texts or standard texts and flat rates

Category

Op. no.

Operation text

Time

Acc. no.

Code

N

025971

OPERATION: REPLACE STEERING SHAFT

0,8 h

46 901 60

LENK-SP3

N

025972

OPERATION: IN ADDITION TO REPLACE STEERING SHAFT, SEPARATE UNIVERSAL JOINT ON THE STEERING SHAFT OF THE STEERING GEAR

0,3 h

46 901 60

LENK-SP3

1

Lower steering shaft

1.1

Upper universal joint

1.2

Lower universal joint

2

Support disk

 Warning

Risk of injury caused by body parts being pinched or crushed as cab is tilted

Ensure that no one is within the tilting range of the cab as it is being tilted. Always tilt the cab all the way to the end position and secure with the safety strut.

AS60.80-Z-0001-01A

Topical note

Notes on tilting the cab

AH60.80-N-0003-01A

Topical note

Notes on self-locking nuts and bolts

AH00.00-N-0001-01A

 

Remove/install

1

Move front wheels to straight-ahead position

 The steering wheel must also be in the straight-ahead position.

2

Open maintenance flap

3

Tilt cab

4

Detach bellows of steering shaft from steering gear and from cab underfloor

5

Detach lower universal joint (1.2) of steering shaft (1) from steering gear

 Check marking on primary shaft for assembly slot of lower universal joint (1.2).
If the assembly slot is offset, the lower universal joint (1.2) should be marked accordingly relative to the primary shaft.

 Installation: The contact surface for the bolt and nut on the lower universal joint (1.2) must be free of grease. Note marking or identification.

 Fit bolt/nut, universal/constant velocity joint

*BA46.10-N-1001-07B

If the lower universal joint (1.2) on the primary shaft of the steering gear is corroded.



Separate lower universal joint (1.2).



AR46.10-W-0510-05A

6

Remove boot from lower steering shaft (1)

7

Mark installation position of upper universal joint (1.1)

 To do so, mark , for example, the position of the assembly slot.

8

Disassemble upper universal joint (1.1) and remove lower steering shaft (1)

 With regard to return shipment or scrapping of removed parts, please observe the information in your warranty system.

 Installation: The contact surface for the bolt and nut on the upper universal joint (1.1) must be free of grease. Note markings and installation position of lower steering shaft (1). The rod (telescopic) must point upwards.

 Fit bolt/nut, universal/constant velocity joint

*BA46.10-N-1001-07B

9

Remove supporting plate (2) from steering gear

 With regard to return shipment or scrapping of removed parts, please observe the information in your warranty system.

 Installation: Grease the top of the steering gear in the area of the sealing ring. Install new support disk (2).

MB high-temperature antifriction bearing grease, 150 g

*BR00.45-Z-1016-06A

10

Install in the reverse order

 Steering wheel, steering column bracket, steering shaft

Number

Designation

Model 375.3/4, 940, 942, 943, 944, 950.5/6, 952.5/6, 953.6, 954.5, 958.2/4

Model 930, 932, 933, 934, 938

BA46.10-N-1001-07B

Fit bolt/nut, universal/constant velocity joint

Nm

30

30

 Steering wheel, steering column bracket, steering shaft

Number

Designation

Model 950.0/1/2/3, 952.0/1/2/3, 953.1/3, 954.0/1/2

BA46.10-N-1001-07B

Fit bolt/nut, universal/constant velocity joint

Nm

30

Repair materials

Number

Designation

Order number

BR00.45-Z-1016-06A

MB high-temperature antifriction bearing grease, 150 g

A 001 989 23 51 10

Parts ordering note

Part no.

Designation

Quantity

A 942 460 50 09 05

Steering shaft (left-hand drive)

1

A 942 460 51 09 05

Steering shaft (right-hand drive)

1

A 942 466 00 96 05

Parts kit for steering gear 765.88

1

A 942 466 01 96 05

Parts kit for steering gear 765.82

1