Remove/install wiper system

เอกสารที่อ้างถึง

AR82.30-P-6400CW

27.9.11

MODEL 204, 207, 212, 218

P82.30-2632-11

Shown on model 204.0/2

1 Driver-side wiper arm

2 Passenger-side wiper arm

3 Frame seal center piece

4 Screw

5 Strut

6 Water collector

P82.30-2665-07

Shown on model 204.0/2

7 Nut

8 Wiper system

11 Bracket

9 Screw

10 Electrical connector

P82.30-2969-04

Model 218

R2/10x1 Wiper park position heater electrical connector

Modification notes

10.8.10

Value changed: Nut for strut to suspension strut tower

*BA62.30-P-1006-02G

 	Remove/install
 Danger!	Risk of injury caused by moving parts that can pinch, crush or, in extreme cases even sever extremities.	Always remove ignition key when working on windshield wiper mechanism.	AS82.30-Z-0001-01A
1	Remove driver-side wiper arm (1) and passenger-side wiper arm (2)		AR82.30-P-6100CW
2	Remove frame seal center piece (3)	In model 204, 207, 212
3	Remove water collector (6)
4	Remove strut (5)	 On model 204 the strut (5) is attached with the bolt (4) of the suspension strut.
			*BA32.25-P-1003-04M
		 On model 207 the strut (5) is fastened below the windshield using the bolt (4) of the suspension strut and two nuts.
			*BA32.25-P-1003-04M
			*BA62.30-P-1007-02G
		 In model 212 and 218 the strut (5) is attached to the mounting console with a nut.
			*BA62.30-P-1006-02G
5	Unscrew bolt (9)	 Do not change installation position of bracket (11) at partition wall, since this would change the contact pressure of the wiper arms and therefore the wiping area.
			*BA82.30-P-1002-01M
6	Unscrew nuts (7)		*BA82.30-P-1003-01M
7	Disconnect electrical connector (10) on wiper motor
8	Unplug wiper park position heater electrical connector (R2/10x1)	Model 218
		 Unplug wiper park position heater electrical connector (R2/10x1) carefully to avoid damaging the wiper park position heater connections. Unlock wiper park position heater electrical connector (R2/10x1) at the catch tab (arrow A), detach from holder and unplug. Unclip wiring harness bracket (arrows B) from wiper system .
9	Remove wiper system (8)
10	Install in the reverse order	 Installation: Before installing a new wiper system (8), the bracket (11) of the new wiper system (8) must be removed.

 Suspension struts

 Suspension struts

Number	Designation		Model 204.08/09/28/29/38/9


BA32.25-P-1003-04M	Suspension strut to body	Nm	33

 Suspension struts

 Front end assembly with front reinforcement

Number	Designation		Model 212	Model 218


BA62.30-P-1006-02G	Nut, strut to suspension strut tower	Nm	30	30

 Front end assembly with front reinforcement

Number	Designation		Model 207.3	Model 207.4


BA62.30-P-1007-02G	Nut, strut to firewall	Nm	35	35

 Windshield wiper

Number	Designation		Model 204	Model 207	Model 212	Model 218


BA82.30-P-1002-01M	Bolt, wiper system to bracket	Nm	11	11	11	11
BA82.30-P-1003-01M	Nut, wiper system to body	Nm	20	22	22	22

Designation

Model 204.00/02/04/05/06/20/22/24/25/
30/33/34/35 without code 483

Model 204.00/02/04/05/06/20/22/24/25/
30/33/34/35
with code 483,
model
204.077/277/
377

BA32.25-P-1003-04M

Suspension strut to body