1 | Rear door |
2 | Front door |
3 | C-pillar |
I | Gap dimension |
M | Gap dimension |
N | Gap dimension |
O | Gap dimension |
S72.12-4526-05
S72.12-4527-09
1 | Rear door | 6 | Nuts | 9 | Nuts | ||
4 | Screw | 7 | Hinge | ||||
5 | Lock striker | 8 | Bolts |
Warning | Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof. | No parts of the body or limbs should be within the operating area when the components are moving. | |
| Check | ||
1 | Check gap dimensions (I, M, N, O) at rear door (1) | ||
Gap dimensions | |||
Gap dimensions | |||
Feeler gauge | |||
2 | Check transition between front door (2) and rear door (1) | Contour of front door (2) must be aligned with contour of rear door (1) or protrude by max. 1 mm. | |
3 | Check transition between rear door (1) and C-pillar (3) | Contour of rear door (1) must be aligned with contour of C-pillar (3) or protrude by max. 1 mm. At the same time, it must be possible to easily close rear door (1). | |
| Remove | ||
4 | Remove lower B-pillar trim from left or right B-pillar | ||
Adjust | |||
5 | Detach screws (4) from lock striker (5) | | |
6 | Detach nuts (6) from hinges (7) and adjust gap dimensions (M, O) and transition between front door (2) and rear door (1) by moving rear door (1) | ||
| |||
Contour of front door (2) must be aligned with contour of rear door (1) or protrude by max. 1 mm. | |||
Helper required. | |||
Gap dimensions | |||
Feeler gauge | |||
7 | Tighten nuts (6) | Nut, top hinge to rear door | |
Nut, lower hinge to rear door | |||
8 | Detach screws (8) and nuts (9) and adjust gap dimensions (N, I) by moving rear door (1) | ||
| |||
Helper required. | |||
Gap dimensions | |||
Gap dimensions | |||
Feeler gauge | |||
9 | Tighten screw/bolts (8) | Bolt, lower edge to B-pillar | |
10 | Tighten nuts (9) | Nut, upper hinge to B-pillar | |
11 | Adjust transition between rear door (1) and C-pillar (3) by moving lock striker (5) | Contour of rear door (1) must be aligned with contour of C-pillar (3) or protrude by max. 1 mm. At the same time, it must be possible to easily close rear door (1). | |
12 | Tighten bolts (4) | Bolt, lock striker to C-pillar | |
13 | Touch up paintwork damage to screws (8) and nuts (9) | ||
| Install | ||
14 | Install lower B-pillar trim on left and/or right B-pillar |
Gap dimensions |
Number | Designation | Model 470, 471 | |||
BE60.00-N-1005-01P | Gap dimensions | Front door to longitudinal member | Dimension "H" | mm | 6 (1,5) |
Front door to rear door | Dimension "I" | mm | 4,4 (1) | ||
Front door to A-pillar | Dimension "J" | mm | 5,5 (1) | ||
Fuel filler flap, all round | Dimension "K" | mm | 3,5 (1) | ||
NOx reducing agent tank filler flap, all round | Dimension "L" | mm | 3,5 (1) | ||
For picture, see | |||||
129 589 03 21 00
Feeler gauge