Shown on model 167.1 except code 414 (Sliding roof) |
1 | Center roof paneling |
P65.10-A013-06
Warning | Risk of injury. Skin or eye injuries may result when handling hot or glowing objects. | Wear protective gloves, protective clothing and safety glasses, if necessary. | |
Caution | Risk of injury caused by scraping or cutting body parts on sharp vehicle parts | Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. | |
Topical note | Information on preventing damage to electronic components due to electrostatic discharge | ||
Topical note | General information on body repair | ||
Topical note | Pretreatment of bonding surfaces | ||
General information on MB materials | |||
| Remove | ||
1 | Remove detachable parts in area of repair point. | ||
2 | Cover all detachable parts remaining in vehicle with spark protection blankets. | ||
3 | Remove center roof paneling (1). |
| |
Model 167.3 | |||
Model 167.9 | |||
1K-zinc dust paint | |||
Set of spacer blocks | |||
| Install | ||
Danger | The high voltage used for electric welding presents a lethal hazard. Risk of explosion from welding in areas close to highly inflammable materials. Risk of injury from weld splatter and UV-light when welding. Risk of poisoning from inhaling welding gases | Use insulating mats. Wear protective clothing, safety glasses and a protective mask. Remove highly inflammable materials from the hazard area. Use air extraction system. | |
Topical note | Measures for preventing damage to components when performing electric welding and soldering work | ||
General information on riveting | |||
4 | Prepare center roof paneling (1). |
| |
Model 167.3 | |||
Model 167.9 | |||
1K-zinc dust paint | |||
5 | Install center roof paneling (1). |
| |
Model 167.3 | |||
Model 167.9 | |||
Blind rivet 6.412 (clamping range 1 mm to 3.5 mm, draw-off strength min. 15.5 kN) | |||
Blind rivet 6.512.5 (clamping range 2 mm to 5 mm, draw-off strength min. 19 kN) | |||
Parts kit for 2-component adhesive for body | |||
Teroson MS 222 | |||
Set of spacer blocks | |||
6 | Clean weld joints and sheet metal flange. | ||
7 | Remove spark protection blankets. | ||
8 | Clean repair area. | ||
9 | Prime repair areas with a primer filler. | ||
Topical note | Notes on paintwork repairs | ||
Use only primer filler approved by Daimler AG: | |||
10 | Seal seam after repair. | ||
11 | Paint repair areas and adjacent surfaces. | ||
Topical note | Notes on paintwork repairs | ||
Use only paints approved by Daimler AG: | |||
12 | Supplement cavity preservation | ||
13 | Reinstall detachable parts in area of repair point. |
216 589 02 23 00
Set of spacer blocks
Repair materials |
Number | Designation | Order number |
BR00.45-Z-1012-13A | Blind rivet 6.512.5 (clamping range 2 mm to 5 mm, draw-off strength min. 19 kN) | A 004 990 16 97 |
BR00.45-Z-1035-13A | Blind rivet 6.412 (clamping range 1 mm to 3.5 mm, draw-off strength min. 15.5 kN) | A 000 991 76 32 |
BR00.45-Z-1056-07A | 1K-zinc dust paint | A 000 986 28 00 |
BR00.45-Z-1157-02A | Teroson MS 222 | A 012 989 14 71 |
BR00.45-Z-1162-02A | Parts kit for 2-component adhesive for body | A 012 989 17 71 |
เอกสารที่อ้างถึง
- ah5400p000101a
- ah6000n000101a
- ah6000p000102a
- ah6000p000301n
- ah6000p000801sx
- ah9800p940802a
- ah9800p940903a
- ar6510p100002me
- ar6510p100002mec
- ar6510p100002mex
- ar6510p100003me
- ar6510p100003mec
- ar6510p100003mex
- ar6510p100007me
- ar6510p100007mec
- ar6510p100007mex
- ar9710p4000me
- ar9720p1500me
- as0000z000201a
- as0000z000701a
- as0000z001701a