Model | 437.42#/43# ## as of 262509 with body 425.840 |
with code F60 (Tilting device for cab) | |
Model | 437.42#/43# ## as of 262509 with body 425.842 |
with code F09 (Cab large) | |
with code F60 (Tilting device for cab) | |
Model | 437.421 ## as of 262509 with body 425.848 |
with code F60 (Tilting device for cab) | |
with code FH6 (Cab, open, with all-weather roof) |
G60.80-A034-79
1 | Engine hood | 9 | Shock absorber | |
2 | Front trim panel | 10 | Screw | |
3 | Air intake hose | 11 | Washer | |
4 | Air intake hose (only for vehicles with code M39 (Alternator 28 V / 100 A, dirt protected)) | 12 | Pin | |
5 | Clip | 13 | Nuts | |
6 | Coolant hose | 14 | Bracket | |
7 | Coolant hoses | A | Drive position | |
8 | Bracket | B | Tilt position |
G60.80-A035-79
15 | Screw | 18 | Fastening console | |
16 | Screw | 19 | Bolts (only on vehicles with code Z16 (Fording capability, special parts)) | |
17 | Step | 20 | Vent housing (only on vehicles with code Z16 (Fording capability, special parts)) |
With code C87 (Exhaust upward) and code MS5 (BlueTec 5) |
21 | Linch pin |
22 | Quick-clamping device |
23 | Bellows |
24 | Exhaust pipe |
G49.10-3164-10
25 | Hydraulic pump |
26 | Locking valve |
27 | Tilt cylinder |
28 | Pump lever |
29 | Safety strut |
30 | Nut |
31 | Steering shaft |
32 | Sliding piece |
C | Tooth gap |
D | Wide tooth |
G60.80-A036-06
Warning | Risk of injury. Skin or eye injuries may result when handling hot or glowing objects. | Wear protective gloves, protective clothing and safety glasses, if necessary. | |
Warning | Risk of injury to skin or eyes from hydraulic fluid spraying out under pressure.Risk of poisoning from swallowing hydraulic fluid. | Depressurize hydraulic system completely before starting any work on it. Wear protective clothing and safety glasses. | |
Warning | Risk of injury caused by body parts being pinched or crushed as cab is tilted | Ensure that no one is within the tilting range of the cab as it is being tilted. Always tilt the cab all the way to the end position and secure it with the safety strut. | |
Topical note | Notes on self-locking nuts and bolts | ||
Topical note | Notes on tilting the cab | ||
Tilt, lower | |||
1 | Remove loose objects from cab. | | |
2 | Close soft top. | Only for model 437.421 with body 425.848 with code FH6 (Cab, open, with all-season soft top) | |
| |||
See supplement "Cab with soft top". | |||
3 | Remove hood (1). | ||
4 | Remove front trim (2). | ||
5 | Remove air conditioner. |
| |
6 | Remove air intake hose (3) and seal both openings, in each case, with a rag. | ||
7 | Remove air intake hose (4) from cab and seal opening with a rag. | Only for vehicles with code M39 (Alternator 28 V/100 A, dirt protected) | |
8 | Remove clamp (5) for coolant hose (6) from bracket. | ||
9 | Remove both coolant hoses (7) from bracket (8). | ||
10 | Remove electric, hydraulic, pneumatic lines and cables and seal. | Only for vehicles with special equipment. | |
See bodybuilder information. | |||
Tilting back: | |||
11 | Remove shock absorbers (9). | On left and right side of vehicle. | |
Screw/nut, shock absorber to cab suspension | |||
12 | Unscrew screws (10) and remove washer (11). | On left and right side of vehicle. | |
Bolt with washer to pin for rocker bearing | |||
13 | Remove nuts (13) and remove bracket (14). | On left and right side of vehicle. | |
Tilting back: | |||
Bolt, rocker bearing to bracket | |||
14 | Clean bolts (12) and grease with long-life grease. | On left and right side of vehicle. | |
Long-life grease | |||
15 | Install bracket (14) with washer (11), screw (10) and nuts (13) in tilt position (B). | On left and right side of vehicle. | |
16 | Tighten screw (10) and nuts (13). | On left and right side of vehicle. | |
Bolt, rocker bearing to bracket | |||
17.1 | Unscrew screws (15, 16) and remove from cab. | Vehicles without air-sprung suspension seat, code DB1, DB3, DF1, DF3 | |
| |||
Inside on driver and passenger side. | |||
Cab to frame and to body support | |||
17.2 | Unscrew screws (15, 16) and remove screws (15) from cab. | Vehicles with air-sprung suspension seat, code DB1, DB3, DF1, DF3 | |
| |||
Inside on driver and passenger side. | |||
Cab to frame and to body support | |||
18 | Remove step (17). | Removal of step (17) facilitates the unimpeded actuation of extension pipe to tilt the cab. | |
19 | Unscrew bolts (19) at vent housing (20) and remove vent housing (20) from mounting support (18). | Only on vehicles with code Z16 (Fording capability, special parts) | |
20 | Remove linch pin (21) and open quick clamping device (22). | Only for vehicles with code C87 (Exhaust upward) and code MS5 (BlueTEC 5) | |
21 | Slide quick clamping device (22) to the side and press boot (23) away from exhaust pipe (24). | Only for vehicles with code C87 (Exhaust upward) and code MS5 (BlueTEC 5) | |
22 | Close locking valve (26) using extension pipe at tilt cylinder (27). | Tilting back: | |
23 | Set pump lever (28) of hydraulic pump (25) to "Lift" position and insert extension pipe in lever of hydraulic pump (25). | ||
24 | Lift cab by approx. 20 cm. | Only for vehicles without air-sprung suspension seat, code DB1, DB3, DF1, DF3 | |
25 | Insert screw (16) at right side of vehicle to secure safety strut (29). | Only for vehicles without air-sprung suspension seat, code DB1, DB3, DF1, DF3 | |
26 | Lift cab until safety strut (29) can be installed. | | |
Only for vehicles with air-sprung suspension seat, code DB1, DB3, DF1, DF3 | |||
Only for vehicles with code M39 (Alternator 28 V/100 A, dirt protected) | |||
Tilting back: | |||
27 | Install safety strut (29) with screw (16), nut (30) and another screw at bottom. | Safety support | |
28 | Grease steering shaft (31) and sliding piece (32). | Long-life grease | |
29 | Tilt back in reverse order. |
435 589 00 63 00
Safety support