MODEL | 218.3 |
MODEL | 218.9 |
Test values for gap dimensions on hoods, doors and lids |
Number | Designation | MODEL 218.9 | MODEL 218.3 | |||
BE60.00-P-1005-01O | Gap dimensions | Liftgate to roof (spoiler removed) | Dimension "R1" | mm | 10 (1,5) | – |
Spoiler to roof | Dimension "R2" | mm | 5,0 (1,5) | – | ||
Liftgate to rear fender | Dimension "P" | mm | 4,5 (1) | – | ||
Liftgate to taillamp | Dimension "V" | mm | 5,0 (1) | – | ||
Liftgate to bumper | Dimension "W" | mm | 6,0 (1,5) | – | ||
Rear window and D-pillar | Dimension "X" | mm | 4,5 (1,5) | – | ||
Rear window to liftgate, bottom | Dimension "Y" | mm | 3,0 (0,5) | – |
Test values for gap dimensions on hoods, doors and lids |
Number | Designation | MODEL 218.9 | MODEL 218.3 | |||
BE60.00-P-1003-01O | Gap dimension | Trunk lid to rear fender, top | Dimension "J" | mm | – | 4,0 (1) |
Trunk lid to rear lamp unit | Dimension "K" | mm | – | 5,0 (1) | ||
Trunk lid to bumper | Dimension "L" | mm | – | 5,5 (1) | ||
Rear fender to lamp unit | Dimension "M" | mm | 2,5 (-1,5/+1) | 3,0 (1) | ||
Picture |
Test values for gap dimensions on hoods, doors and lids |
Number | Designation | MODEL 218.9 | MODEL 218.3 | |||
BE60.00-P-1001-01O | Gap dimension | Engine hood to fender | Dimension "A" | mm | 4,0 (1) | 4,0 (1) |
Engine hood to headlamp | Dimension "B" | mm | 4,0 (1) | 4,0 (1) | ||
Engine hood to bumper | Dimension "C" | mm | 4,0 (1) | 4,0 (1) | ||
Engine hood to A-pillar | Dimension "Q" | mm | 4,5 (1) | 4,5 (1) | ||
Fender to headlamp | Dimension "R" | mm | 4,0 (1) | 4,0 (1) | ||
Bumper to headlamp (circumferential) | Dimension "S" | mm | 3,5 (1) | 3,5 (1) | ||
Mounting rail, bumper to engine hood | Dimension "T" | mm | 7,5 (+0,5) | 7,5 (+0,5) | ||
Mounting rail, bumper to engine hood | Dimension "U" | mm | 1,0 (0,5) | 1,0 (0,5) | ||
Picture |
Test values for gap dimensions on hoods, doors and lids |
Number | Designation | MODEL 218.9 | MODEL 218.3 | |||
BE60.00-P-1002-01O | Gap dimension | Fender to A-pillar | Dimension "D" | mm | 3,5 (1) | 3,5 (1) |
Front door to fender | Dimension "E" | mm | 4,0 (-0,5/+1) | 4,0 (-0,5/+1) | ||
Front door to rear door | Dimension "F" | mm | 5,0 (-0,5/+1) | 5,0 (-0,5/+1) | ||
B-pillar cover to front window | Dimension "G" | mm | 10 (1) | 10 (1) | ||
B-pillar cover to rear window | Dimension "H" | mm | 10 (1) | 10 (1) | ||
Rear door to side piece, bottom | Dimension "I" | mm | 4,5 (1) | 4,5 (1) | ||
Fixed window on rear door to fixed window on rear side window | Dimension "O" | mm | 7,5 (1) | – | ||
Picture |
129 589 03 21 00
Feeler gauge
Adjust hoods, doors and cover according to drawing with feeler gauge. The gap should not run wedge-shaped or be too narrow at points. Deviations from parallel gap should be max. 0.5 mm over the entire length. If the inside clearance is too large or too small, the movable body parts must be centered accordingly. The reference measurements apply only for repair work on bodies damaged in accidents.
Shown on model 219 |
P60.00-2618-06
Shown on model 219 |
P60.00-2619-06
Illustrated on model 218.3 |
P60.00-2892-06
Shown on model 218.9 |
P60.00-2974-06