| Remove | ||
Danger | Risk of fire/risk of explosion due to short circuit and escaping oxyhydrogen gas. Risk of (burn) injury caused by caustic burns to eyes, skin and mucous membranes from battery electrolyte/mist, short circuit and arcing. Risk of poisoning caused by swallowing battery electrolyte or absorption of lead through the skin or body orifices. Risk of death due to voltage U >= 30 V AC and U >= 60 V DC. | No fires, sparks, open flames, or smoking. Wear acid-resistant gloves, clothing, and glasses. Pour battery acid only into suitable and appropriately marked containers. | |
Topical note | Notes on battery | ||
1 | Unhook load compartment cover in trunk | Model 230 for checking on-board electrical system battery. | |
2 | Remove spare tire cover | For checking on-board electrical system battery. | |
3 | Open engine hood and move to vertical position |
| |
| Check | ||
4 | Perform visual inspection of battery for external leakage | If leakage found, install new battery, see: | |
Dispose of defective battery properly and in an environmentally compatible manner. | |||
| |||
Remove/install battery | |||
| |||
| |||
| |||
5.1 | Check fluid level in battery, replenish with distilled water if necessary | Without service fill level indicator, not on absorbent glass mat battery. | |
5.2 | Check fluid level of battery | With service fill level indicator, not on absorbent glass mat battery. | |
Fluid level indicator via service fill level indicator, if color is white, the acid level is too low: Replace battery, see: | |||
Dispose of defective battery properly and in an environmentally compatible manner. | |||
| |||
Remove/install battery | |||
| |||
| |||
6 | Check battery | ||
Cold cranking amps as per EN | |||
Commercially available devices/tools | |||
Battery capacity 12 Ah | |||
Battery capacity 30 Ah | |||
Battery capacity 35 Ah | |||
Battery capacity 46 Ah | |||
Battery capacity 60 Ah VRLA/AGM | |||
Battery capacity 60 Ah | |||
Battery capacity 62 Ah | |||
Battery capacity 70 Ah VRLA/AGM | |||
Battery capacity 74 Ah | |||
Battery capacity 80 Ah VRLA/AGM | |||
Battery capacity 84 Ah | |||
Battery capacity 90 Ah VRLA | |||
Battery capacity 95 Ah VRLA | |||
Battery capacity 100 Ah | |||
7 | Reduce increased voltage after charging process | On a battery that is disconnected from the on-board electrical system and with a "Surface voltage" message in the display of the Midtronics battery tester/test equipment. | |
After reducing increased voltage, test battery again. | |||
Commercially available devices/tools | |||
8 | Charge battery | With test code "Charge and check" of Midtronics battery tester/test equipment. | |
After charging, test battery again. | |||
Commercially available devices/tools | |||
| Install | ||
9 | Close engine hood |
| |
10 | Install spare tire cover | After checking the on-board electrical system battery. | |
11 | Hook in trunk load compartment cover | Model 230 after checking on-board electrical system battery. |
Test and adjustment values for battery |
Number | Designation | Model all (4xWD, CAR, smart) | |||
BE54.10-P-1002-01A | Battery capacity 30 Ah | Battery test at 20 °C | Acid density | kg/dm3 | 1,24 |
Maximum permissible difference between individual battery cells | kg/dm3 | 0,04 | |||
Load current | A | 90 | |||
Load time | s | 10 | |||
Voltage | V | 10 | |||
Cold cranking amps | As per EN | A | 540 |
Test and adjustment values for battery |
Number | Designation | Model all (4xWD, CAR, smart) | |||
BE54.10-P-1003-01A | Battery capacity 35 Ah | Battery test at 20 °C | Acid density | kg/dm3 | 1,24 |
Maximum permissible difference between individual battery cells | kg/dm3 | 0,04 | |||
Load current | A | 100 | |||
Load time | s | 10 | |||
Voltage | V | 10 | |||
Cold cranking amps | As per EN | A | 520 |
Test and adjustment values for battery |
Number | Designation | Model all (4xWD, CAR, smart) | |||
BE54.10-P-1005-01A | Battery capacity 46 Ah | Battery test at 20 °C | Acid density | kg/dm3 | 1,24 |
Maximum permissible difference between individual battery cells | kg/dm3 | 0,04 | |||
Load current | A | 140 | |||
Load time | s | 10 | |||
Voltage | V | 10 | |||
Cold cranking amps | As per EN | A | 420 |
Test and adjustment values for battery |
Number | Designation | Model all (4xWD, CAR, smart) | |||
BE54.10-P-1009-01A | Battery capacity 62 Ah | Battery test at 20 °C | Acid density | kg/dm3 | 1,24 |
Maximum permissible difference between individual battery cells | kg/dm3 | 0,04 | |||
Load current | A | 190 | |||
Load time | s | 10 | |||
Voltage | V | 10 | |||
Cold cranking amps | As per EN | A | 480 |
Test and adjustment values for battery |
Number | Designation | Model all (4xWD, CAR, smart) | |||
BE54.10-P-1011-01A | Battery capacity 74 Ah | Battery test at 20 °C | Acid density | kg/dm3 | 1,24 |
Maximum permissible difference between individual battery cells | kg/dm3 | 0,04 | |||
Load current | A | 265 | |||
Load time | s | 10 | |||
Voltage | V | 10 | |||
Cold cranking amps | As per EN | A | 680 |
Test and adjustment values for battery |
Number | Designation | Model all (4xWD, CAR, smart) | |||
BE54.10-P-1016-01A | Battery capacity 100 Ah | Battery test at 20 °C | Acid density | kg/dm3 | 1,24 |
Maximum permissible difference between individual battery cells | kg/dm3 | 0,04 | |||
Load current | A | 300 | |||
Load time | s | 10 | |||
Voltage | V | 10 | |||
Cold cranking amps | As per EN | A | 760 |