AR49.10-W-5530A | Remove/install exhaust pipe | 21.2.12 |
ENGINE 904.9 in MODEL 375, 958, 970, 972, 975, 976
ENGINE 906.9 in MODEL 958, 970, 972, 974, 975, 976
ENGINE 924.9 in MODEL 958
ENGINE 924.9 in MODEL 970, 972, 974, 975, 976 except CODE (MS4) BlueTec 4
ENGINE 924.9 in MODEL 970, 972, 974, 975, 976 except CODE (MS5) BlueTec 5
W49.10-1051-09
Shown on ENGINE 904.9 in MODEL 970
1 Exhaust pipe
2 Clip
3 Exhaust connection (on engine without code (MB1) Engine brake with constant throttle)
8 Exhaust flex pipe
9 Muffler
5 Bracket
6 Clip
7 Clip
W49.10-1054-02
Only for engine 906.9
1 Exhaust pipe
2 Clip
4 Engine brake flap connection
10 Control lever
A Distance
Arrow Stop
| Remove/install | ||
| Notes on self-locking nuts and bolts | ||
1 | Switch off ignition | ||
Danger! | Risk of explosion caused by escaping oxyhydrogen gas. Risk of injury caused by caustic burns to eyes, skin and mucous membranes from battery electrolyte (contains diluted sulfuric acid) or metal spatter due to short circuit. Risk of burn injuries caused by short circuit. Risk of poisoning caused by swallowing battery electrolyte (contains diluted sulfuric acid) or absorption of lead over the skin or orifices | No fire, sparks, open flames or smoking. Wear acid-resistant gloves and clothing and safety glasses with side guards. Do not place any conductive objects on the battery and avoid any short circuit from battery positive to ground. Only fill liquid battery electrolyte (diluted sulfuric acid) into suitable and appropriately marked containers. | |
2 | Disconnect ground lead from battery | ||
| Notes on battery | ||
Danger! | Risk of injury caused by body parts being pinched or crushed as cab is tilted | Ensure that no one is within the tilting range of the cab as it is being tilted. Always tilt the cab all the way to the end position and secure with the safety strut. | |
3 | Tilt cab | Installation: Only tilt cab back after leak test has been conducted. | |
| Notes on tilting the cab | ||
4 | Remove soundproofing on frame above on the right | ||
5.1 | Detach clamp (2) at exhaust connection (3) | Engine without code (MB1) Engine brake with constant throttle | |
| |||
5.2 | Detach clamp (2) at engine brake valve fitting (4) | Engine with code (MB1) Engine brake with constant throttle | |
Installation: Pay attention to the installation position of clamp (2) on engine 906.9. There must be a distance (A) of min. 20 mm between the bolt head on the clamp (2) and the end stop (arrow) of the adjusting lever (10). | |||
| |||
6 | Detach clamp (6) at bracket (5) and detach bracket (5) at timing case | Installation: Align clamp (6) and bracket (5) with the timing case, then tighten clamp (6) and bracket (5). | |
| |||
7 | Release clamps (7) and push backwards at the exhaust pipe (1) as well as at the fitting of the muffler (9) and remove exhaust flex pipe (8) | Installation: Check exhaust flex pipe (8) for damage; replace if necessary. Pay attention to the installation position of the clamps (7), the bolts must point upwards. | |
| |||
| Assembly notes and installed dimensions for exhaust flex pipes | ||
8 | Remove exhaust pipe (1) | ||
9 | Install in the reverse order | ||
Danger! | Risk of accident caused by vehicle starting off by itself when engine is running. Risk of injury caused by contusions and burns during starting procedure or when working near the engine as it is running | Secure vehicle to prevent it from moving by itself. | |
10 | Start the engine and check the exhaust system for leaktightness, then turn off the engine | ||
11 | Synchronize the time of the record sheet admission | Only on vehicles with MTCO tachograph. |
Exhaust system
Number | Designation | Engine | ||
BA49.10-N-1001-01O | Bolt, clamp to exhaust pipe, muffler and exhaust flex pipe | Nm | 50 | |
BA49.10-N-1002-01O | Bolt, exhaust pipe clamp to engine brake flap fitting/exhaust connection | Nm | 15 | |
BA49.10-N-1004-01O | Bolt, clamp to holder | Nm | 50 | |