P42.10-2964-09
Shown on MODEL 222 - right side of vehicle |
1 | Bolts | 9 | Brake disk | M76/1 | Left electric parking brake actuator motor | ||
2 | Caliper support | 10 | Brake linings | M76/2 | Right electric parking brake actuator motor | ||
3 | Brake caliper | 11 | Spring steel sheets | S10/4 | Right rear brake wear sensor | ||
5 | Guide pin | 12 | Bellows | S10/4x1 | Right rear brake wear sensor electrical connector | ||
6 | Brake hose | 16 | Electric line |
01 | Pusher tool |
3 | Brake caliper |
13 | Dust boot |
P42.10-2868-11
Caution | Risk of poisoning from swallowing brake fluid. Risk of injury from skin and eye contact with brake fluid | Only pour brake fluid into suitable and appropriately marked containers. Wear protective clothing and eye protection when handling brake fluid. | |
Warning | Risk of injury. Skin or eye injuries may result when handling hot or glowing objects. | Wear protective gloves, protective clothing and safety glasses, if necessary. | |
Topical note | Brake fluid notes | ||
Topical note | Notes on self-locking nuts and bolts | ||
Topical note | Notes on repairs to brake system | ||
Notes on installing brake wear indicator contact sensors | |||
| Remove/install | ||
1 | Move brake pads (10) of the rear axle into assembly position | ||
| |||
The engine hood must be closed. | |||
2 | Switch off ignition and remove transmitter key | ||
3 | Remove cover over brake fluid expansion reservoir | ||
| Clean | ||
4 | Clean area surrounding the cap of the brake fluid expansion reservoir | Assembly cleaner | |
5 | Unscrew the cap on the brake fluid expansion reservoir and suction off some brake fluid | In order to prevent the brake fluid expansion reservoir overflowing when pressing back the brake pistons. | |
6 | Detach corresponding complete wheel | ||
7 | Disconnect right rear brake wear sensor electrical connector (S10/4x1) from right rear brake wear sensor (S10/4) | When removing brake linings (10) on right side of vehicle | |
8 | Detach electrical connection from left electric parking brake actuator motor (M76/1) or right electric parking brake actuator motor (M76/2) | ||
9 | Remove bolt (1) from lower guide pin (5) | Counterhold lower guide pin (5) while doing so. | |
Guide pin to brake caliper support or bolt for guide pin to brake caliper | |||
10 | Swivel brake caliper (3) upwards | Do not detach brake hose (6). | |
Installation: Guide the right rear brake wear sensor (S10/4) through the opening of the brake caliper (3). | |||
11 | Remove brakepad (10) from brake caliper support (2) | Installation: Only sets of brake linings (10) approved by Mercedes-Benz may be installed. Do not apply brake paste or lubricants to the brakepads (10) and brake calipers (3)! | |
12 | Pull right rear brake lining wear sensor (S10/4) out of brake lining (10) | When removing brake linings (10) on right side of vehicle | |
Installation: Replace defective right rear brake lining wear sensor (S10/4). | |||
13 | Remove spring steel sheets (11) from brake caliper support (2) | ||
Checking, measuring | |||
14 | Check condition of brake linings (10) | ||
| Model 217 | ||
| Model 222 | ||
If necessary: | |||
| |||
Replace brake linings (10). | |||
15 | Check condition of brake disk (9) and gauge degree of wear | ||
| Model 217 | ||
| Model 217 | ||
| Model 222 | ||
| Model 222 | ||
If necessary: | |||
| |||
Replace brake disk (9). | |||
16 | Check brake caliper (3) and dust boot (13) on brake piston for damage | If damage is present: | |
| |||
Replace brake caliper (3). | |||
17 | Check boots (12) for damage and correct seat | If damage is present: | |
| |||
Replace brake caliper support (2). | |||
18 | Check guide pin (5) for ease of movement | Replace brake caliper support (2) if damaged, see: | |
| |||
Replace brake caliper (3). | |||
19 | Press back brake piston using pusher tool (01) | Resetting device | |
If the brake piston is difficult to move: | |||
| |||
Replace brake caliper (3). | |||
| Clean | ||
20 | Clean contact surfaces of brake linings (10) on brake caliper (3) and on brake caliper support (2) | | |
Assembly cleaner | |||
21 | Install in the reverse order | ||
Danger | Risk of accident when commissioning the vehicle due to a lack of braking effect when the service brake is operated for the first time after repair work. | Before starting the engine, actuate brake pedal several times until pressure is built up and maintained in the brake system. | |
22 | Depress brake pedal several times until brake pads (10) rest against brake disks (9) | ||
| Check | ||
23 | Check fluid level in brake fluid expansion reservoir | ||
| |||
24 | Carry out brake test on the test stand | ||
|
000 589 52 43 00
Resetting device