W41.10-1034-09
Shown on drivetrain with a propeller shaft intermediate bearing and without code B3G (Permanent magnet retarder) |
1 | Propeller shaft | 4 | Propeller shaft intermediate bearing flange connection | |
2 | Permanent clevis | 5 | Propeller shaft intermediate bearing | |
3 | Rear axle flange connection | 6 | Transmission flange connection |
Warning | Risk of injury. Moving parts can pinch, crush or, in extreme cases even sever extremities. | No parts of the body or limbs should be within the operating area of mechanical components when moving components. | |
Danger | Risk of death for persons with implants caused by work on permanent magnet retarder. Risk of injury caused by burns due to contact with hot rotor. | As a safe distance from the permanent magnet retarder, a minimum distance of 30 cm is to be maintained between the permanent magnet retarder and the body parts of the affected person for people with implants. | |
Danger | Risk of death caused by vehicle slipping or toppling off during lifting | Only lift vehicle at the lift support points specified by the vehicle manufacturer. | |
Topical note | Notes on removal/installation of propeller shafts | ||
Topical note | Special instructions for lifting and supporting vehicle | ||
Notes on safety-relevant components | |||
| Remove/install | ||
1 | Secure vehicle to prevent it moving away. | ||
2 | Switch off ignition. | ||
3 | Lift and support vehicle at one side of rear axle. | Only in case of poor accessibility of threaded connections at rear axle flange connection (3), propeller shaft intermediate bearing flange connection (4), transmission flange connection (6). | |
Only raise until the wheel rotates freely. | |||
4 | Secure propeller shaft (1) using tensioning straps against falling down. | ||
5 | Detach propeller shaft (1) from rear axle flange connection (3). | Propeller shaft to flange connection | |
Open end wrench | |||
Open-end wrench | |||
Open-end wrench insert | |||
Open wrench insert, (18 mm) | |||
Torque wrench handle | |||
6 | Detach propeller shaft (1) from propeller shaft intermediate bearing flange connection (4). | Only for vehicles with propeller shaft center support bearing (5) when only one individual propeller shaft (1) of the drive train is to be removed,installed, or when the propeller shaft center support bearing (5) is to be replaced. | |
Propeller shaft to flange connection | |||
Open end wrench | |||
Open-end wrench | |||
Open-end wrench insert | |||
Open wrench insert, (18 mm) | |||
Torque wrench handle | |||
7.1 | Detach propeller shaft (1) from transmission flange connection (6). | Vehicles without code B3G (Permanent magnet retarder) | |
Propeller shaft to flange connection | |||
Open end wrench | |||
Open-end wrench | |||
Open-end wrench insert | |||
Open wrench insert, (18 mm) | |||
Torque wrench handle | |||
7.2 | Detach propeller shaft (1) at permanent magnet retarder flange connection. | Vehicles with code B3G (Permanent magnet retarder) with propeller shaft intermediate bearing | |
Propeller shaft to flange connection | |||
Screw/bolt, intermediate bearing to bracket | |||
7.3 | Detach propeller shaft (1) at permanent magnet retarder flange connection. | Vehicles with code B3G (Permanent magnet retarder) without propeller shaft intermediate bearing | |
Propeller shaft to flange connection | |||
8 | Detach propeller shaft intermediate bearing (5) from holder. | Only on vehicles without code B3G (Permanent magnet retarder) and with propeller shaft intermediate bearing. | |
Screw/bolt, intermediate bearing to bracket | |||
9 | Remove propeller shaft(1). | Remove propeller shaft (1) downward using telescopic lifter and with a help of another person. | |
10 | Install in the reverse order. |
000 589 29 01 00
Open-end wrench insert
001 589 44 21 00
Torque wrench handle
000 589 22 01 00
Open-end wrench
000 589 30 01 00
Open wrench insert, (18 mm)
000 589 21 01 00
Open end wrench