Remove/install propeller shaft

AR41.10-B-0050TA

01.07.2019

Model

693.0/1/2/3, 694.0, 695.01/04/3, 696.0/3, 934.2, 936.315, 938.14, 958.0/1/2/4, 979.0

Modification notes

17.06.2019

Fully revised document.

W41.10-1034-09

Represented in the power train with the intermediate bearing transmission shaft

1	Propeller shaft	4	Intermediate bearing drive shaft flange connection
2	Stationary fork	5	Transmission shaft intermediate bearing
3	Rear axle flange connection	6	Gearbox flange connection

 	Remove/install
 Warning	Risk of injury. Moving parts can pinch, crush or, in extreme cases even sever extremities.	No parts of the body or limbs should be within the operating area of mechanical components when moving components.	AS00.00-Z-0009-01A
 Danger	Risk of death caused by vehicle slipping or toppling off during lifting	Only lift vehicle at the lift support points specified by the vehicle manufacturer.	AS00.00-Z-0032-01A
Topical note	Notes on removal/installation of propeller shafts	.	AH41.10-N-0003-01A
Topical note	Special instructions for lifting and supporting vehicle	.	AH00.60-N-0100-01B
	Notes on self-locking nuts and bolts		AH00.00-N-0001-01A
1	Protect the vehicle against involuntary movement
2	Turn off ignition
3	Lift the vehicle on one side of the rear axle and support it	Only with the threaded coupling on the rear axle flange connection (3), to the flange connection of the intermediate bearing transmission shaft (4), to the gearbox flange connection (6).
		 Lift enough to allow free wheel rotation only.
4	Ensure the drive shaft (1) with tensioning straps to prevent fall
5	Remove the transmission shaft (1) from the rear axle drive flange connection (3)	 .Screw and nut of the propeller shaft on the flange	*BA41.10-B-1004-01H
		 Open-end wrench socket (21_mm)	*000589310100
		 Open wrench insert, (18 mm)	*000589300100
		 Open-end wrench insert	*000589290100
		 Open end wrench	*000589210100
		 Open-end wrench	*000589220100
		 Open-end wrench	*000589230100
		 Open wrench	*000589260100
		 Torque wrench handle	*001589442100
6	Remove the transmission shaft (1) from the intermediate bearing rear axle drive flange connection (4)	Only in the case of vehicles with an intermediate bearing transmission shaft (5), if only one single drive shaft (1) of the power train has been removed, installed, or if the drive shaft of the intermediate bearing (5) has to be replaced.
		 .Screw and nut of the propeller shaft on the flange	*BA41.10-B-1004-01H
		 Open-end wrench socket (21_mm)	*000589310100
		 Open wrench insert, (18 mm)	*000589300100
		 Open-end wrench insert	*000589290100
		 Open end wrench	*000589210100
		 Open-end wrench	*000589220100
		 Open-end wrench	*000589230100
		 Open wrench	*000589260100
		 Torque wrench handle	*001589442100
7	Remove the transmission shaft (1) from the rear axle drive flange connection (6)	 .Screw and nut of the propeller shaft on the flange	*BA41.10-B-1004-01H
		 Open-end wrench socket (21_mm)	*000589310100
		 Open wrench insert, (18 mm)	*000589300100
		 Open-end wrench insert	*000589290100
		 Open end wrench	*000589210100
		 Open-end wrench	*000589220100
		 Open-end wrench	*000589230100
		 Open wrench	*000589260100
		 Torque wrench handle	*001589442100
8	Remove the transmission shaft intermediate bearing support	Only in vehicles with transmission shaft intermediate bearing (5).
		.	AR41.40-B-0001TA
		 M12x1,5	*BA00.10-B-1008-03A
9	Remove the transmission shaft (1) from below	 With the aid of a second person.
10	Install in reverse order

 Tables-DIN tightening torques according to MBN 10 142

Number	Designation		Steel 8,8	10,9 Steel
BA00.10-B-1008-03A	M12x1,5	Nm	68	100

 Propeller shaft

Number	Designation			Type 934.241/251, 936.14, 938.14, 958.4	Model 958.0/1/2
BA41.10-B-1004-01H	Screw and nut of the propeller shaft on the flange	M10	Nm	-	60
		M12	Nm	-	100
		M14	Nm	-	160
		M16	Nm	-	200