S35.30-A001-09
1 | Slotted nut | 5 | Brake carrier plate | 9 | Locking pawl | ||
2 | Lock washer | 6 | Wheel bolt | A | Pressure padding | ||
3 | Wheel bearings | 7 | Oil collector | B | Assembly sleeve | ||
4 | Wheel bearing housing | 8 | Rear axle shaft |
Caution | Risk of injury to skin and eyes due to handling of transmission oil. Health risk caused by swallowing transmission oil | Wear protective gloves, protective clothing and safety glasses. | |
Caution | Risk of injury caused by scraping or cutting body parts on sharp vehicle parts | Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. | |
Note on calculation of tightening torque when using insertion or socket tools with various effective lengths | |||
| Remove | ||
1 | Remove rear axle shaft (8). | ||
2 | Remove pulse ring. | ||
| Disassemble | ||
3 | Release locking pawl (9) of retaining washer (2). | Use suitable tool to bend open locking pawl (9). | |
4 | Remove slotted nut (1). | Dispose of slotted nut (1). | |
Slotted nut wrench | |||
5 | Remove retaining washer (2). | Dispose of retaining washer (2). | |
6 | Remove wheel bearing (3) with wheel bearing housing (4) from rear axle shaft (8). | Attach extractor as shown and clamp in vise. | |
Secure rear axle shaft (8) against falling down. | |||
Dispose of wheel bearing (3) and wheel bearing housing (4). | |||
Commercially available devices/tools | |||
Puller | |||
7 | Detach brake carrier plate (5) from rear axle shaft (8). | ||
8 | Press out inner wheel bearing cage. | If still fitted. | |
To do so, attach puller to the inner wheel bearing cage and use the workshop press to press the rear axle shaft (8) out of the inner wheel bearing cage. | |||
Secure rear axle shaft (8) against falling down. | |||
Commercially available devices/tools | |||
Puller | |||
9 | Drive out all wheel studs (6). | Dispose of wheel studs (6). | |
Puller | |||
10 | Remove oil collector (7) from rear axle shaft (8). | Dispose of oil collector (7). | |
| Check | ||
11 | Check brake carrier plate (5) for damage. | If damage exists, | |
| |||
Replace brake carrier plate (5). | |||
12 | Check rear axle shaft (8) for damage. | If damage exists, | |
| |||
Replace rear axle shaft (8). | |||
| Clean | ||
13 | Clean rear axle shaft (8) or brake carrier plate (5). | In case of recycling. | |
Assembly cleaner | |||
| Assemble | ||
14 | Attach new oil collector (7) to rear axle shaft (8). | ||
15 | Insert new wheel studs (6) through oil collector (7) into wheel hub. | To do so, align bores of oil collector (7) with corresponding bores of wheel hub. | |
16 | Draw in new wheel studs (6). | To do so, position suitable washer and suitable nut on respective wheel stud (6) and tighten nut until the collar of the wheel stud (6) makes contact with the contact surface of the oil collector (7). | |
17 | Attach brake carrier plate (5) to rear axle shaft (8). | Pay attention to installation position. | |
18 | Press wheel bearing (3) into wheel bearing housing (4), as shown. | | |
Use suitable drift to press in wheel bearing (3) up to end stop. | |||
Commercially available devices/tools | |||
19 | Press wheel bearing (3) with wheel bearing housing (4) onto rear axle shaft (8). | | |
Install sealed side of wheel bearing (3) on outward facing side of wheel bearing housing (4). | |||
Commercially available devices/tools | |||
20 | Fit new retaining washer (2) over the rear axle shaft (8), onto the wheel bearing (3). | ||
21 | Install new slotted nut (1). | Nut, rear axle shaft to wheel bearing | |
Slotted nut wrench | |||
22 | Secure slotted nut (1) against twisting using a retaining washer (2). | To do so, lock slotted nut (1) using one of the locking pawls (9) and a suitable tool. | |
| Install | ||
23 | Install pulse ring. | ||
24 | Install rear axle shaft (8). |
454 589 00 33 00
Puller
470 589 09 33 00
Puller
001 589 19 33 00
Puller
470 589 02 07 00
Slotted nut wrench