AR35.25-D-2300H | Remove/install rubber mount on semi-trailing arm | 29.1.10 |
REAR AXLE 741.417 in MODEL 906.132 /134 /136
D35.25-1106-06
1 Semi-trailing arm
2 Link rod
3 Shock absorber
4 Link rod
5 Nut
6 Screw
7 Screw
8 Transmission jack
9 Hollow cylinder
10 Press-out sleeve
11 Friction disks
12 Nut
13 Threaded rod
14 Pulling-in sleeve
| Remove/install | ||
Danger! | Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between columns of vehicle lift and position four support plates at vehicle lift support points specified by vehicle manufacturer. | |
1 | Remove rear wheels | ||
2 | Loosen link rod (4) of height sensor on one side | With code (LG0) bi-xenon headlamp or code (LG1) bi-xenon headlamp with corner-illuminating fog lamps | |
3 | Support semi-trailing arm (1) using transmission jack (8) | Transmission jack 2.0-7.0 t gotis://H_00.10_01.0 | |
Transmission platform for passenger cars and commercial vehicles gotis://A_25/35/49_02.0 | |||
4 | Unscrew link rod (2) for anti-sway bar on semi-trailing arm (1) | | |
5 | Unscrew damper (3) on semi-trailing arm (1) | | |
6 | Unscrew bolts (6, 7) | Installation: Install new nut (5). Only tighten the nut (5) slightly. Final tightening with tightening torque only takes place after adjusting the semi-trailing arm. | |
| |||
7 | Unhook semi-trailing arm (1) | ||
8 | Press rubber mount out of semi-trailing arm (1) | Press out rubber mount using hollow cylinder (9) and remover (10). | |
| |||
| |||
| |||
| |||
9 | Moisten new rubber mount slightly with lubricant | ||
Antifriction agent | |||
10 | Press in new rubber bushing | Attach remover (10) to semi-trailing arm (1). Mount hollow cylinder (9) with threaded rod (13) and from the other side slide pull-in sleeve (14) with new rubber mount and friction disks (11) onto threaded rod (13). Screw on nut (12) until it is flush in insertion sleeve (14). Pull in rubber mount with hollow cylinder (9). Check that rubber bushing is positioned centrally via inspection window in remover (10). | |
If the rubber mount was drawn in too far, mount hollow cylinder (9) and remover (10) as mating bearing on the opposite side and thus pull the rubber mount over the threaded rod (13) in the correct position. | |||
| |||
| |||
| |||
| |||
11 | Install in the reverse order | ||
12 | Check and adjust toe on rear axle |
Semi-trailing arm
Number | Designation | Rear axle 741.417 | |||
BA35.15-N-1001-01B | Bolt/nut, semi-trailing arm to subframe | M141.5 | Stage 1 | Nm | 160 |
Stage 2 | ° | 120 | |||
Anti-roll bar
Number | Designation | Model | ||
BA32.35-N-1005-03B | Bolt/nut, link rod | M10 10.9 | Nm | 54 |
Rear axle shock absorber
Number | Designation | Model | |||
BA32.25-N-1003-03A | Bolt, shock absorber to semi-trailing arm low frame | M141.5 | Nm | 130 | |
652 589 00 33 21
Hollow cylinder
Hand pump
Pressing tool
Hydraulic hose (complete)
906 589 02 43 00
652 589 00 33 22
652 589 00 33 23
Repair materials
Number | Designation | Order number |
BR00.45-Z-1032-06A | Antifriction agent | A 000 989 08 60 |