B35.20-0044-09
1 | Outer grooved nut | 8 | Wheel hub | |
2 | Lock plate | 9 | Wheel screws | |
3 | Inner grooved nut | 10 | Race ring | |
4 | Ring gear | 11 | Claw type wrench | |
5 | Outer planetary gear carrier | 12 | Mandrel | |
6 | Lock-ring | 13 | Inside seal | |
6A | Wire retaining ring | 14 | Outside seal | |
7 | Tapered roller bearing |
| Remove | ||
1 | Remove the bell hub with the planetary gear carrier |
| |
2 | Remove the ABS system sensor | Vehicles equipped with anti-lock brake system ABS. | |
3 | Release the locking of the outer slotted nut (1) and remove it | Claw-type wrench | |
4 | Remove the lock plate (2) and the inner slotted nut (3) | Claw-type wrench | |
5 | Remove the ring gear (4), assembled with the outer planetary gear carrier (5) and the retaining ring (6) or the (6A) from the crease of the axle spindle | There are two types of retaining rings: the SEEGER type (6), and the wire retaining ring (6A). | |
6 | Block the wheel hub (8) | ||
7 | Remove the wheel hub (8) and the tapered roller bearing (7) | The inner race of the tapered roller bearing (7) will come out together the wheel hub. | |
8 | Remove the ABS tone wheel, if necessary | Vehicles equipped with anti-lock brake system ABS. | |
9 | Remove, if necessary, the oil baffle and, next, the outer seal (14) and inner seal (13) | Puller | |
| Check | ||
10 | Check the wear the friction surface of the race (10) |
| |
If the race (10) shows damage, wear and/or grooves on its friction surface: | |||
| |||
Remove and replace with a new one. | |||
| Install | ||
11 | Install the race ring (10) |
| |
Only in case of replacement. | |||
Confirm the correct position of the race (10) on the axle. | |||
12 | Install the inner seals (13) and the outer seal (14) and the oil baffle |
| |
Pay attention to the correct arrangement of the seals. The inner seal (13) has only one lip, while the outer seal (14) has two. | |||
Apply sealant on the oil pan fitting | |||
Use new seals (13, 14). | |||
Terolan 307/II, Dichtin 51, epple 22 sealant | |||
Drift | |||
Drift | |||
13 | Install the ABS tone wheel | Vehicles equipped with anti-lock brake system ABS. | |
14 | Install the wheel hub (8) on the axle | | |
15 | Install the outer bearing (7) on the wheel hub (8) | Lubricate the bearing with grease. | |
Grease, DB supply specification 6804 - Class 267.0 | |||
Drift | |||
Drift | |||
16 | Install the ring gear (4), assembled with the outer planetary gear carrier (5) and the retaining ring (6) or the (6A) from the crease of the axle spindle |
| |
There are two types of retaining rings: the SEEGER (6) and the wire retaining ring (6A). | |||
17 | Install the inner slotted nut (3), the lock plate (2), and the outer slotted nut (1) | Claw-type wrench | |
18 | Adjust the wheel hub bearing clearance |
| |
.Axial clearance of wheel hub bearings | |||
Claw-type wrench | |||
19 | Lock the lock plate (2) on the outer slotted nut (1) | ||
20 | Install the ABS sensor | Vehicles equipped with anti-lock brake system ABS. | |
. | |||
21 | Install the bell hub on the planetary gear carrier |
|
055 589 21 15 00
Drift
000 589 16 33 00
Puller
740 589 00 07 00
Claw-type wrench
055 589 19 15 00
Drift
321 589 02 15 00
Drift
363 589 05 15 00
Drift
Repair materials |
Number | Designation | Order number |
BR00.45-Z-1018-01A | Terolan 307/II, Dichtin 51, epple 22 sealant | Use corresponding commercially available repair materials. |
BR00.45-Z-1107-06A | Grease, DB supply specification 6804 - Class 267.0 | Use corresponding commercially available repair materials. |