G33.10-3109-09
Shown on front axle 737.365
1 Wheel speed sensor connector
2 Brake wear indicator connector
3 Brake hose
4 Brake line
5 Locking plate
12 Steering knuckle arm
13 Transverse control arm
14 Torque tube
15 Screw
16 Screw
17 Propeller shaft
6 Compressed air lines
7 Screw
8 Shock absorber
9 Screw
10 Stabilizer link bracket
11 Drag link
Modification notes
| Remove/install | ||
Danger! | Risk of poisoning caused by swallowing brake fluid. Risk of injury caused by brake fluid coming into contact with skin and eyes. | Only pour brake fluid into suitable and appropriately marked containers. Wear protective clothing and eye protection when handling brake fluid. | |
| Notes on self-locking nuts and bolts | All models | |
1 | Disconnect connectors of wheel speed sensors (1) | ||
2 | Disconnect connector of brake wear indicator (2) | ||
3 | Separate brake hoses (3) from brake lines (4) | Seal brake hoses (3) and brake lines (4). | |
4 | Pull out locking plate (5) of brake hoses (3) and remove brake hoses (3) from bracket | ||
5 | Detach compressed air lines (6) from frame transverse pipe | ||
6 | Remove bolt (7) of shock absorber (8) | | |
7 | Remove bolt (9) from stabilizer link bracket (10) on axle side | | |
8 | Detach drag link (11) from steering knuckle arm (12) and secure above | Steering 765.863 | |
Steering ZF 8095 | |||
9 | Remove transverse control arm (13) on the frame side | | |
10 | Place jack stand under torque tube (14) | ||
11 | Remove bolts (15) of torque tube (14) from front axle output shaft | Installation: Clean sealing surfaces and use sealing compound. | |
| |||
12 | Using chain hoist, pull front axle slightly away from transfer case | In order to gain access to the bolts (16) of the propeller shaft (17). | |
13 | Remove bolts (16) of propeller shaft (17) | Do not let the propeller shaft (17) hang down, secure it instead, as the brake lines are overtensioned and are damaged as a result. | |
| |||
Installation: Before installing the propeller shaft (17) on the output flange, the torque ball of the torque tube (14) must be adjusted: | |||
Adjust preload of torque tube to torque ball housing | |||
| |||
14 | Using a hoist system, raise vehicle slightly at front plate and roll out front axle toward front | With the aid of a second fitter. | |
15 | Put down vehicle on support stands under frame | ||
16 | Install in the reverse order | ||
17 | Check compressed air lines (6) for leaks | ||
18 | Check function of differential lock | ||
19 | Check oil level and correct if necessary | ||
| Front axle - Checking and correcting oil level | ||
20 | Bleed brake system |
Front axle shock absorber
Number | Designation | Model | |
BA32.25-N-1001-01E | Nut/bolt, shock absorber to front axle | Nm | 250 |
Trailing arms, wishbones
Number | Designation | Front axle | Front axle | |
BA33.15-N-1003-01D | Bolt, stabilizer to bracket | Nm | 150 | 150 |
BA33.15-N-1004-01D | Bolt, transverse control arm to frame | Nm | 315 | 315 |
Front axle drive
Number | Designation | Front axle 737.365/375 | Front axle | ||
BA33.30-N-1008-01F | Bolt, torque ball housing to transfer case | Nm | 60 | 60 | |
Propeller shaft
Number | Designation | Model 437 | |
BA41.10-N-1001-01J | Bolt, propeller shaft to front axle output flange | Nm | 100 |
Installation flange
425 589 00 59 00
Repair materials
Number | Designation | Order number |
BR00.45-Z-1015-01A | Loctite 5203 sealant | A 002 989 71 20 10 |