1 | Nuts |
2 | Cover |
3 | Heat shield |
7 | Nut |
10 | Bracket |
11 | Air intake hose |
14 | Pressure line |
16 | Bracket |
A9/1 | AIR BODY CONTROL compressor |
P32.22-2624-06
4 | Electrical connectors |
5 | Cable tie |
6 | Pressure line connection |
11 | Air intake hose |
14 | Pressure line |
15 | Bracket |
16 | Bracket |
A9/1 | AIR BODY CONTROL compressor |
P32.22-2625-06
Shown on rear elastomer bearing (12) |
7 | Nut |
8 | Threaded rod |
9 | Washer |
12 | Elastomer bearing |
13 | Protective sleeve |
17 | Compression spring |
A9/1 | AIR BODY CONTROL compressor |
P32.22-2626-03
Warning | Risk of injury. Skin or eye injuries may result when handling hot or glowing objects. | Wear protective gloves, protective clothing and safety glasses, if necessary. | |
Caution | Risk of injury caused by scraping or cutting body parts on sharp vehicle parts | Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. | |
Topical note | Notes on self-locking nuts and bolts | ||
Notes on AIRmatic | |||
| Remove | ||
1 | Raise vehicle. | ||
2 | Remove nuts (1) and remove cover (2). | ||
3 | Extend heat shield (3) out of stud bolts and push to one side. | ||
4 | Disconnect electrical connections (4). | ||
5 | Separate cable ties (5) and place electric lines to one side. | ||
6 | Remove pressure line connection (6) from AIR BODY CONTROL compressor (A9/1) and seal openings using suitable stop plugs. | Record plug | |
7 | Unclip pressure line (14) from holder (15). | ||
8 | Unscrew nuts (7) and remove AIR BODY CONTROL compressor (A9/1) downwards. | ||
9 | Unclip air intake hose (11) at holder (16). | When replacing AIR BODY CONTROL compressor (A9/1). | |
10 | Remove air intake hose (11) from AIR BODY CONTROL compressor (A9/1). | When replacing AIR BODY CONTROL compressor (A9/1). | |
11 | Remove holders (15, 16) from AIR BODY CONTROL compressor (A9/1). | When replacing AIR BODY CONTROL compressor (A9/1). | |
| Check | ||
12 | Check holder (10) and threaded rods (8) for damage. | If there are problems with the holder (10) or threaded rods (8), | |
| |||
replace holder (10). | |||
13 | Check elastomer bearings (12) for damage and wear. | If there is a problem, | |
| |||
replace elastomer bearings (12). | |||
| Install | ||
14 | Mount holders (15, 16) onto AIR BODY CONTROL compressor (A9/1). | When replacing AIR BODY CONTROL compressor (A9/1). | |
15 | Attach air intake hose (11) to AIR BODY CONTROL compressor (A9/1). | When replacing AIR BODY CONTROL compressor (A9/1). | |
16 | Clip air intake hose (11) onto holder (16). | When replacing AIR BODY CONTROL compressor (A9/1). | |
17 | Place washers (9) onto elastomer bearings (12). | ||
18 | Fit compression springs (17) onto protective sleeves (13). | ||
19 | Position protective sleeves (13) with compression springs (17) into elastomer bearings (12). | ||
20 | Position AIR BODY CONTROL compressor (A9/1) and tighten nuts (7). | Nut, compressor mounting to compressor unit bracket | |
21 | Clip pressure line (14) into holder (15). | ||
22 | Remove all stop plugs. | ||
23 | Attach pressure line connection (6) to AIR BODY CONTROL compressor (A9/1). | | |
Pressure line to compressor/valve unit (P) | |||
Torque tool set | |||
Torque wrench | |||
If thread is damaged, | |||
| |||
Repair pressure line connection (6). | |||
Knife | |||
24 | Attach new cable ties (5). | ||
25 | Contact electrical connectors (4). | ||
26 | Replace AIR BODY CONTROL relay. | When replacing AIR BODY CONTROL compressor (A9/1). | |
| Assignment of engine fuse and relay module | Model 213.088/089/288/289 | |
| Check | ||
Warning | Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | |
27 | Perform an engine test run and check air suspension for proper operation. | ||
28 | Check all compressed-air connections at AIR BODY CONTROL compressor (A9/1) for leak tightness. | ||
| Install | ||
29 | Move heat shield (3) into stud bolts. | ||
30 | Position cover (2) and tighten nuts (1). | ||
31 | Lower vehicle fully. |
001 589 86 21 00
Torque wrench
000 589 12 28 00
Knife
129 589 00 91 00
Record plug
003 589 05 09 00
Torque tool set