1 | Automatic transmission fluid cooler |
2 | Screw |
3 | Bracket |
4 | Transmission oil lines |
5 | Coolant hoses |
6 | Bolts |
7 | Oil pan |
D27.55-A012-76
Danger | Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer. | |
Warning | Risk of injury to skin and eyes suffering scalding from contact with hot coolantspray. Risk of poisoning from swallowing coolant. | Do not open cooling system unless coolant temperature is below 90 °C. Open cap slowly and release the pressure. Do not pour coolant into beverage containers. | |
Caution | Risk of injury to skin and eyes due to handling of transmission oil. Health risk caused by swallowing transmission oil | Wear protective gloves, protective clothing and safety glasses. | |
Topical note | Notes on avoiding damage through contamination and foreign objects | ||
Notes on automatic transmission | |||
| Remove | ||
1 | Unscrew cap from coolant expansion reservoir. | ||
2 | Raise vehicle. | ||
Topical note | Special instructions for lifting and supporting vehicle | ||
3 | Remove lower engine compartment paneling. | Model 907.6 with code XM1 (Noise abatement measures) | |
4 | Thoroughly clean automatic transmission oil cooler (1) and the area surrounding it. | Assembly cleaner | |
5 | Loosen screw (2), turn holder (3) by 90° and unhook transmission oil lines (4) from holder (3). | ||
6 | Remove transmission oil lines (4) from automatic transmission fluid cooler (1) and seal openings with suitable stop plugs. | ||
Collect any transmission oil which runs out. | |||
Assembly cleaner | |||
Record plug | |||
7 | Clamp off coolant hoses (5). | Clamp | |
8 | Remove coolant hoses (5) from automatic transmission fluid cooler (1) and seal openings with suitable protective covers. | ||
Collect escaping coolant. | |||
Set of protective caps | |||
9 | Unscrew screws (6) and remove automatic transmission fluid cooler (1) from oil pan (7). | ||
| Install | ||
10 | Position automatic transmission fluid cooler (1) on oil pan (7). | ||
11 | Screw in bolts (6). | Screw, oil cooler to oil pan | |
12 | Remove protective covers from coolant hoses (5) and automatic transmission oil cooler (1). | ||
13 | Attach coolant hoses (5) to automatic transmission fluid cooler (1). | ||
14 | Remove clamping devices from coolant hoses (5). | ||
15 | Remove stop plugs and attach transmission oil lines (4) to automatic transmission fluid cooler (1). | ||
16 | Position transmission oil lines (4) in installation position, turn holder (3) by 90° and screw in screw (2). | Screw, holder for oil lines to oil pan top section | |
| Check | ||
17 | Correct coolant level and check engine cooling system for leak tightness. | ||
Model 907.6 with code XM1 (Noise abatement measures) | |||
18 | Check/correct automatic transmission fluid level. | ||
| Check | ||
Warning | Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | |
19 | Perform engine test run and check in area of automatic transmission fluid cooler (1) for leak tightness. | ||
20 | Install lower engine compartment paneling. | Model 907.6 with code XM1 (Noise abatement measures) | |
000 589 54 37 00
Clamp
001 589 00 91 00
Set of protective caps
129 589 00 91 00
Record plug