AR26.60-W-6420C | Adjust shifter | 3.11.10 |
TRANSMISSION 710.6 in MODEL 970.###, 972.###, 975.###, 976.### 1# with CODE (GS1) "Manual" gearshift
TRANSMISSION 712.62 in MODEL 375.1##, 958.0##, 970.###, 972.###, 976.### 1# with CODE (GS1) "Manual" gearshift
TRANSMISSION 712.63, 715.060 in MODEL 970.###, 972.###, 974.###, 976.### 1# with CODE (GS1) "Manual" gearshift
TRANSMISSION 712.63 in MODEL 958.0## 1# with CODE (GS1) "Manual" gearshift
TRANSMISSION 712.611, 715.050 in MODEL 970.###, 972.###, 976.### 1# with CODE (GS1) "Manual" gearshift
TRANSMISSION 715.320 in MODEL 970.###, 972.###, 974.###, 976.### 1#
TRANSMISSION 715.320 in MODEL 375.3## 1#
W26.60-1024-02
10 Gearshift lever
11 Adjusting device
12 Probe
13 Gearshift boot
Modification notes
| Removing | ||
Danger! | Risk of injury caused by body parts being pinched or crushed as cab is tilted | Ensure that no one is within the tilting range of the cab as it is being tilted. Always tilt the cab all the way to the end position and secure with the safety strut. | |
1 | Tilt cab | ||
| Notes on tilting the cab | ||
2 | Detach shift lever knob from gearshift lever (10) | ||
3 | Detach gearshift boot (13) with carrier from gearshift lever (10) | ||
| Checking | ||
4 | Place gearshift lever (10) in neutral position | ||
5 | Attach adjusting device (11) | Screw the probe (12) into the threaded hole of the adjusting device according to the transmission model and cab designation. | |
Transmission 712.611, 712.62/63, 715.050/060 with cab designations 375.830, 972.899 into threaded hole "G56; G60/G85-A". | |||
With cab designations 375.850, 958.860 and 972.890 into threaded hole "G56;G60/G 85-B". | |||
On vehicles with four cylinder engines. | |||
On vehicles with six cylinder engines. | |||
| Service Information: Special tool modification | ||
6 | Place probe (12) on centering bore at gearshift lever (10) and adjust shift mechanism if necessary | Do not bend the probe (12). It must be possible to position the probe (12) at the center of the upper centering bore of the gearshift lever; if necessary, adjust the rear gate support and longitudinal support: | |
Transmission 712.611, 712.62/63, 715.050/060 | |||
Transmission 710.6 | |||
Transmission 715.320 | |||
Transmission 715.320 | |||
Transmission 715.320 | |||
| Install | ||
7 | Detach adjusting device (11) | ||
8 | Perform a function test | Shift through all gears, | |
Repeat adjustment procedure. | |||
9 | Install gearshift boot (13) with supporting bracket | ||
10 | Install shift lever knob on gearshift lever (10) | Transmissions 712.62/63, 715.050/060 | |
Transmission 710.6 | |||
Transmission 715.320 | |||
Transmission 712.611 | |||
Danger! | Risk of injury caused by body parts being pinched or crushed as cab is tilted | Ensure that no one is within the tilting range of the cab as it is being tilted. Always tilt the cab all the way to the end position and secure with the safety strut. | |
11 | Lower cab | ||
| Notes on tilting the cab |
Shift mechanism
Number | Designation | Trans-mission | Trans-missions | |
BA26.60-N-1012-01B | Nut, shift lever knob to shift lever | Nm | 20 | 20 |
Shift mechanism
Number | Designation | Trans-mission | |
BA26.60-N-1005-01C | Nut, shift lever knob to shift lever | Nm | 14 |
Shift mechanism
Number | Designation | Transmission | ||
BA26.60-N-1003-01F | Lock nut, control valve to shift rod | Nm | 150 | |
BA26.60-N-1004-01F | Lock nut, shift gate support | Nm | 55 | |
BA26.60-N-1012-01F | Nut, shift lever knob to shift lever | Nm | 20 | |
Shift mechanism
Number | Designation | Trans-mission | ||
BA26.60-N-1008-01G | Nut, shift lever knob to shift lever | Nm | 20 | |
970 589 01 23 00
Adjusting device
Adjusting device
970 589 00 23 00