Remove/install MR/PLD injection lines

AR07.15-W-9235A

19.9.06

ENGINE 904.9 in MODEL 668, 670

ENGINE 904.9 in MODEL 374, 375, 673, 674, 676, 958, 970, 972, 975, 976

ENGINE 906.9 in MODEL 374, 958, 970, 972, 974, 975, 976

ENGINE 906.9 in MODEL 374, 375, 950, 952, 953, 954, 958

ENGINE 906.9 in MODEL 957 except CODE (MS8) Natural gas engine

W07.15-0085-12

Shown on engine 904.9

1 Engine trim panel

2 Injection lines

Modification notes

26.4.01

Value changed from 25 Nm to 35 Nm

Figure in BA07.15-N-1004-01A for engine 904.9, 906.9 modified

*BA07.15-N-1004-01A

	Removing
 Danger!	Risk of injury caused by body parts being pinched or crushed as cab is tilted	Ensure that no one is within tilting range of the cab as it is being tilted. Always tilt cab all the way to the end position and secure with the safety strut.	AS60.80-Z-0001-01A
1.1	Tilt cab	Model 374, 375, 673, 674, 676, 950, 952, 953, 954, 957, 958, 970, 972, 974, 975, 976
	Notes on tilting the cab		AH60.80-N-0003-01A
1.2	Remove service cover	Model 668, 670
2	Remove side soundproofing on the left	 Only for model 374, 375, 673, 674, 676, 950, 952, 953, 954, 957, 958, 970, 972, 974, 975, 976.
3	Remove engine panel (1)
 Danger!	Risk of explosion caused by fuel igniting, risk of poisoning caused by inhaling and swallowing fuel and risk of injury to eyes and skin caused by contact with fuel	No fire, sparks, open flames or smoking. Only pour fuels into suitable and appropriately marked containers. Wear protective clothing when handling fuel.	AS47.00-Z-0001-01A
4	Remove injection line (2)		*000589070300
			*000589680300
	Install
 Danger!	Risk of explosion caused by fuel igniting, risk of poisoning caused by inhaling and swallowing fuel and risk of injury to eyes and skin caused by contact with fuel	No fire, sparks, open flames or smoking. Only pour fuels into suitable and appropriately marked containers. Wear protective clothing when handling fuel.	AS47.00-Z-0001-01A
5	Install injection lines (2)	 Do not bend injection lines (2); note installation position.
			*BA07.15-N-1004-01A
			*000589070300
			*000589680300
 Danger!	Risk of accident caused by vehicle starting off by itself when engine is running. Risk of injury caused by contusions and burns during starting procedure or when working near the engine as it is running	Secure vehicle to prevent it from moving by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts.	AS00.00-Z-0005-01A
6	Start the engine and bleed the fuel system	 The fuel system is bled automatically. Allow engine to run for about 1 minute; repeat starting procedure after 2 minutes if the engine stops or does not start.
7	Turn off engine
8	Check injection lines (2) for leaks by means of a visual inspection	 Also replace corresponding injection line (2) if necessary.
9	Install engine panel (1)
10	Remove side soundproofing on the left	 Only for model 374, 375, 673, 674, 676, 950, 952, 953, 954, 957, 958, 970, 972, 974, 975, 976.
 Danger!	Risk of injury caused by body parts being pinched or crushed as cab is tilted	Ensure that no one is within tilting range of the cab as it is being tilted. Always tilt cab all the way to the end position and secure with the safety strut.	AS60.80-Z-0001-01A
11.1	Lower cab	Model 374, 375, 673, 674, 676, 950, 952, 953, 954, 957, 958, 970, 972, 974, 975, 976
	Notes on tilting the cab		AH60.80-N-0003-01A
11.2	Install service cover	Model 668, 670

 Diesel injection system with unit pumps (MR/PLD)

Number	Designation		Engine 904.9, Engine 906.9 without code MS8


BA07.15-N-1004-01A	Injection line to pressure pipe connection and unit pump	Nm	35

000 589 68 03 00

Box wrench bit

Ring wrench

000 589 07 03 00

เอกสารที่อ้างถึง