Represented in Engine 926.9 |
1 | Engine coating |
2 | Holder (only for code (GS3) "Hydraulic" clutch) |
3 | Holder (only for code (GS3) "Hydraulic" clutch) |
W07.15-1445-06
W07.15-1446-08
4 | Injection pipe | 8 | Impact puller | Y9 | Unit pump 4th cylinder | ||
5 | Electric harness of the engine | Y6 | Single pump cylinder 1 | Y10 | Single pump 5th cylinder | ||
6 | Bolts | Y7 | Unit pump 2nd cylinder | Y11 | Single pump 6th cylinder | ||
7 | Roller tappet | Y8 | Unit pump 3rd cylinder |
| Remove | ||
Danger | Risk of explosion caused by fuel igniting, risk of poisoning caused by inhaling and swallowing fuel as well as risk of injury to eyes and skin caused by contactwith fuel. | No fires, sparks, open flames or smoking. Pour fuels into suitable and appropriately marked containers only. | |
1 | Turn off ignition | ||
Topical note | Notes on tilting the cab | ||
Warning | Risk of injury caused by body parts being pinched or crushed as cab is tilted | Ensure that no one is within the tilting range of the cab as it is being tilted. Always tilt the cab all the way to the end position and secure it with the safety strut. | |
2 | Tilt the cabin | ||
3 | Remove the upper left chassis acoustic encapsulation | ||
4 | Remove the engine coating (1) | ||
5 | Clean the engine block in the area of the corresponding injecting unit | ||
6 | Remove injecting pipe (4) from the corresponding injecting unit |
| |
7 | Identify the injecting unit in relation to each cylinder | Only when removing several injecting units. | |
8 | Remove holder of gear lever in the head | Only in vehicles with code (GS1) "mechanical" gear command and for removal of the injecting unit from 1st cylinder (Y6). | |
9 | Remove holder (2) of the hydraulic pipe and holder (3) | Only in vehicles with code (GS3) "hydraulic" gear command and for removal of the injection unit from 1st cylinder (Y6). | |
Do not separate hydraulic pipes. | |||
10 | Remove fixing ruler for the electric harness of the engine (5) with Start Engine and Stop Engine buttons in the engine block | Only necessary if, in the engine 924.9, the injection unit of cylinder 2 (Y7) or the injection unit of cylinder 3 (Y8) is removed i.e. in engine 926.9, the injection unit of cylinder 4 (Y9) or the injection unit of cylinder 5 (Y10) is removed. | |
11 | Separate the electric harness of the engine (5) in the corresponding injecting unit | ||
12 | Loosen the screws (6) of the corresponding injection unit and unscrew approx. 4 to 5 mm | The injecting unit is under tension force and may be thrown out if hit when screws are being loosened (6) from the engine block and, therefore, it may be damaged. | |
13 | Install impact drawer (8) in the respective injecting unit | Impact extractor | |
14 | Remove the respective injecting unit with the impact drawer (8) up to the top of the screws (6) | A stuck injection unit cannot be removed from the electromagnet valve or from housing flange, because it may damage the electromagnet valve. | |
15 | Remove impact drawer (8) | ||
16 | Remove screws (6) and its respective injecting units | ||
17 | Check the roller tappet (7) in the respective injective unit | | |
Check the surface of the roller tappet (7); in case of minor grooves and scratches, the injecting unit may be used. In grooves, scratches or deep sanded spots: | |||
| |||
Replace the respective injecting unit; furthermore, check visually the rebound of the injecting unit in the camshaft. | |||
| Install | ||
18 | Clear carefully any impurity and paint residues on the sealing surface of the engine block | Close the drilling in the engine block. | |
19 | Install new O-rings in the injecting unit with grease | Only when reinstalling previously run injecting units. | |
Apply grease softly on the body of the injecting unit and in the drilling in the engine block | |||
High-temperature grease | |||
Sleeve | |||
20 | Install the injecting unit in the engine block and screw evenly | Do not damage the O-rings in the body of the injecting unit. | |
Engine block injection unit | |||
21 | Install the fixing ruler for the electric harness of the engine (5) with Start Engine and Stop Engine buttons in the engine block | Only necessary if, in the engine 924.9, the injection unit of cylinder 2 (Y7) or the injection unit of cylinder 3 (Y8) is installed i.e. in engine 926.9, the injection unit of cylinder 4 (Y9) or the injection unit of cylinder 5 (Y10) is installed. | |
22 | Connect the electric harness of the engine (5) in the corresponding injecting unit | ||
23 | Install holder of gear lever in the head | Only in vehicles with code (GS1) "mechanical" gear command and for removal of the injection unit from 1st cylinder (Y6). | |
24 | Install holder (2) of the hydraulic pipe and holder (3) | Only in vehicles with code (GS3) "hydraulic" gear command and for removal of the injection unit from 1st cylinder (Y6). | |
25 | Install injecting pipe (4) from the corresponding injecting unit | ||
Warning | Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | |
26 | Execute test run to check the engine, turn it off and search the area of the injecting unit for any leakages | Actuate the starter for no more than 90 seconds. The fuel system bleeds automatically. Should the engine not stop or not start, repeat the start procedure after waiting 2 minutes. | |
27 | Connect Star Diagnosis and reprogram the bar code of the injecting unit | Only in case of installation of new injecting units. | |
28 | Install the engine coating (1) | ||
29 | Install acoustic insulation on the left upper frame | ||
Warning | Risk of injury caused by body parts being pinched or crushed as cab is tilted | Ensure that no one is within the tilting range of the cab as it is being tilted. Always tilt the cab all the way to the end position and secure it with the safety strut. | |
30 | Return the cab to its position | ||
Topical note | Notes on tilting the cab |
904 589 03 14 00
Sleeve
355 589 01 63 00
Impact extractor